Main
Notebook Computer
Model No. CF-18NHHZXBM
This apparatus must be earthed for your safety.
For U.K.
1
WARNING
LASER SAFETY INFORMATION
Page
Page
CONTENTS
Page
1.2. Troubleshooting
1-2
2-1
2 Power-On Self Test (Boot Check)
Outline of POST
Error Diagnosis by Checking Beep Signal Sound
3. List
Page
4. Diagnostic Test
4.1 Equipment
4.2 Preparation
Insert the diagnostics floppy disk
Return the setup contents to default Choose test from the menu screen to start the test.
5 Self Diagnosis Test
5.1. Outline of Self Diagnostic Tests
5.1.1 List of main test items
5.2. Automatic Test
5-2
5.3. Peripheral Test
3. LAN Test
4. Modem Test 5. Wireless LAN Test
5-3
5 .4. Test Selection
5-4
Input screen startup
End of test
5-5
Example: "AL T" + "F" brings up the File menu.
Order of test flow selection
5.5 . Error Messages and Troubleshooting
5-6
6 Wiring Connection Diagram
6-1
7 Disassembly/Reassembly
7.1. Disassembly Instructions
7.1.1. Preparation
7.1.2. Removing the Battery Pack and HDD Pack
7.1.3. Removing the Touch Pad and Key- board
7.1.4. Removing the Speaker Angle and DIMM Lid
7.1.5. Removing the Rear Cabinet
7.1.6. Removing the DU Lid Unit
7.1.7. Removing the Audio PCB
7.1.8. Removing the Wireless Module, Port PCB and Modem
7.1.9. Removing the SD PCB
7.1.10. Removing the Main PCB and Lith- ium Battery
7.1.11. Removing the PAD PCB and I/O PCB
7.1.12. Removing LED PCB and Switch PCB
7.1.13. Removing the CPU Heat Plate
7.1.14. Removing the Display unit
7.1.15. Removing the LCD Rear Case
7.1.16. Removing the LCD Hinge
7.1.17. Removing Inverter PCB and LCD Unit
7.1.18. Removing GPRS Antenna PCB, LAN1-BT PCB, LAN2-BT PCB, Wide Area Aux PCBand Pen Holder
7.1.19. Removing the Each Cover
7-7
7.2. Reassembly Instructions
CD
LCD Back Cushion S
B
Detail of "A"
A
Safety Working
Insert between the ribs.
Insert between the ribs.
(Hold the Connector part when connecting /disconnecting.)
7-9
! Assembly of Inverter PCB (Applicable Model : Digitizer Model)
TS Spacer A
Laminate film
Attach the surface to the LCD Front.
7-10
! Assembly of Glass (Applicable Model : Digitizer Model)
Glass Assy
7-11
7.2.3. Assembling GPRS Antenna PCB, LAN1-BT PCB, LAN2-BT PCB, Wide Area Aux PCB, and Pen Holder
! Line processing of Antenna Cable
B
C
A
7.2.4. Setting up the LCD Hinge
7-13
! Line processing of Antenna Cable and LCD Cable
Protect Sheet
ANT Cable
Safety Working
Lock Plate Assy
Cable Holder
LCD Cable Holder Sheet
7-14
7.2.5. Assembling the Anntena Cover, the Tablet Latch Cover and the LCD Rear Case
! Assembly of LCD Front Case
Page
7-16
! Assembly of Tablet Latch Cover and Antenna Cover
7.2.6. Setting the Display Unit
7-18
7.2.7. Setting the CPU Heat Plate
Tape
! Line Processing of the Modem Cable, and putting of the Heatsink Rubber.
1. Fix the CPU Heat Plate using the three Screws<R>. Screws <R>:DFHE5025XA
CPU Heat Plate
7.2.8. Setting the LED PCB and the Switch PCB
! Assembly of the LED PCB and the Switch PCB
Operation Sheet
Operation Tape
LED Light Guide Sheet
7.2.9. Setting the PAD PCB and the I/O PCB
PAD PCB
PAD FFC
SW FFC
7-21
PAD Card Insulation Sheet
Core side
Dont overflow.
! Assembly of TOP CASE ASSY
Front side Right side
7.2.10. Setting the Main PCB and the Lithium Battery
! Line Processing of the Antenna Cable
7-23
! Line Processing of Main Unit
Lithum Battery
After attaching the Cushion for Lithum Battery, set the Lithum Battery as shown below.
Cushion for Lithum Battery
CN3
7-24
7.2.11. Setting the SD PCB
DIMM Holder
SD Sheet
! Assembly of SD PCB
SD PCB
7.2.12. Setting the Wireless Module, the Port PCB, and the Modem
Port PCB
DU Connetor Angle Tape DU Sponge B DU Sponge D
Antenna PCB
Portre Sheet
7-26
! Line Processing of the Wireless Module,Port PCB and Modem
PCMCIA Sheet
Tape
..
7.2.13. Setting the Audio PCB
7.2.14. Assembling the DU Lid Unit
Audio PCB
Sheet(for EMI)
Audio FFC
7.2.15. Setting the Rear Cabinet
! Cautions for Setting the Rear Cabinet
7.2.16. Setting the Speaker and Dimm Lit
DIMM Lid
DIMM Lid Assy
7.2.17. Setting the Touch Pad and the Keyboard
7-31
! Putting of the Sheet
7-32
! Cautions for Setting the Keyboard
3~5mm
Remove the Release Paper, and then attach the Palmrest Assy.
Release Paper
7.2.18. Setting the Battery Pack and the HDD Pack
HDD Case A
Revision Label
FPC(HDD) HDD Spacer C
FPC ASSY
7.2.19. Assembling the Each Cover
8 Exploded View
Screw tightening torque
Screw tightening torque
A B C E
Screw tightening torque
0.2 _ 0.02N m (2.0 _ 0.2kgf cm)
A+
Screw tightening torque
0.2 _ 0.02N m (2.0 _ 0.2kgf cm) 0.12 _ 0.01N m (1.2 _ 0.1kgf cm)
A D
Screw tightening torque
0.2 _ 0.02N m (2.0 _ 0.2kgf cm) 0.8 _ 0.08N m (8.0 _ 0.8kgf cm)
B D
Screw tightening torque
0.18 _ 0.02N m (1.8 _ 0.2kgf cm)
A
Screw tightening torque
B C D
9 Replacement Parts List
Page
Page
Page
Page
Page
Replacement Parts List
CF-18NHHZXBM PART NO. DESCRIPTION Q'TY MAIN PCB
A
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
AUDIO PCB
Page
I/O PCB
PAD PCB
SWITCH PCB
LED PCB
PORT PCB
TS PS2 PCB
SD PCB