Maytag W10239207B installation instructions Control SET-UP Procedures, Display, SET-UP Codes

CONTROL SET-UP PROCEDURES

IMPORTANT: Read all instructionsbeforeoperating.

The fabric settingbuttonsalong with the digitaldisplayare used to set-up the dryer controls.

The display can contain4 numbers and/orlettersand a decimal point. These are used to indicatethe set-up codes and relatedcode values available for use in programming the dryer.

How to use the buttons to program the controls

1.The WHITES AND COLORSbuttonis used to adjustthe valuesassociatedwith set-upcodes. Pressingthe buttonwill increment the value by one (1). Rapid adjustmentis possible by holding the button down.

2.The PERM. PRESS button advancesthe displaythroughthe set- up codes. Pressing the buttonwill advancethe displayto the next availableset-upcode. Holding the buttondown will automatically advance throughthe set-upcodes at a rate of one (1) per second.

3.The DELICATESbuttonis used to selector deselectoptions.

Start Operating Set-Up

■PD Models: Insert service door key, turn, and lift to remove access door.

■PN Models: Remove the AA1 jumper fromthe controlboard, see procedurebelow,or use the ServiceAccessCode below.Oncethe debit card readeris installed(accordingto the reader manufacturer’s instructions),the set-upmode can be enteredby inserting a manual set-up card (supplied by the readermanufacturer)into the cardslot. If manual set-up cardis not available,manualset-upmode cannot be entered.However,diagnosticmode can be enteredby removing connector AA1 on the circuitboard.

IMPORTANT: The console must not be openedunlesspower is first removed from the dryer.To access connectorAA1:

￿Unplug dryer or disconnectpower.

￿Open console, disconnectplug on AA1, close console.

￿Plug in dryer or reconnectpower.

■PN Models Equipped with ProgrammingSwitch:Insertaccess panel key and turn counter-clockwise.

■PN Models with Gen. 2 Debit Card Reader:Once a Gen. 2 debit card reader is installed (accordingto the readermanufacturer’s instructions), the set-up mode can only be enteredby inserting a manual set-up card (supplied by the readermanufacturer) into the card slot.

If manual set-up card is not available, only diagnosticmode can be entered.

■Alternate methodof entering Set-up Mode by enteringService Access Code: This code can be enteredto accessset-upmode without removing the consoleon dryers just removedfrom the carton, or not yet programmed. The ServiceAccessCode only functions on dryers set up for 0 vend price withoutany Special Pricing set-up,and the Coin/Debit Optionmust be set to “J._d”. If the dryer is not in failure mode, the door must be openedto proceed. Using only the threebottombuttons(numbered1, 2, and 3 from left to right):

1. Press 2 for longer than 2 secondsbut less than 10 seconds.

2. Press 1 & 3 simultaneously for 2 seconds.Displayshows S 3.

3. Press 1 & 2 simultaneously. Display shows S 4.

4. Press 2 & 3 simultaneously. Display shows S 5.

5. Press 2.

6. Waitat least 2 seconds, but not more than 15 seconds, then pressin succession:3, 2, 1, 3.

The dryer is now in the set-up mode.

Before proceeding, it is worth notingthat, despiteall the options available, an owner can simply chooseto uncratea new commercial dryer, hook it up, plug it in, and have a dryer that operates.NOTE: PD models require a payment systemor OPL kit to be installedprior to operation.

■PD dryersarepre-set at the factory for fixedcyclepricewithtop off.

■PN dryers are pre-set for fixed cycle operation,and they can be run withoutpayment.

DISPLAY

After the dryer has been installed and plugged in, the display will show ‘0 minutes.’

Once the dryer has been plugged in and the dryer door opened and closed, the display will show the vend price. PN models are factorypresetfor freecycles;the displaywillflash‘SELECTCYCLE’.

PD Models

PRICE

PN Models

SET-UP CODES

FOR PN MODELS: The set-up codes are the same as for the PD models except where noted.

The set-up code is indicated by the one or two left hand characters. The set-up code value is indicated by the two or three right hand characters.

NOTE: The first line of each code indicates the factory default.

	CODE			EXPLANATION
	6		0 6	REGULAR CYCLE PRICE
6		0 6		Represents the number of coins(coin 1); may adjust from 0-39
				(See b.xx set-up for VALUE OF COIN1). Advance from0-39 by
				pressing WHITESAND COLORS. Factory default of 6 x coin 1.
6		0 0		PN MODELSONLY: Factorydefault of 6 00, or 0 coins.

￿Press PERM. PRESS buttononce to advanceto next code.

	70	5	REGULAR DRY TIME
70		5	Represents the number of minutes per coin (coin 1).
			Factorydefaultof 5 minutes per coin.
			Example:6 coins x 5 minutes = 30 minutes.
			By pressing the WHITES ANDCOLORS button,value adjusts
			from1-99minutes.
74		5	PN MODELS: Representsthe cycle lengthfor free cycles.
			As example: ‘7 45’ = 45 minutes.

￿Press PERM. PRESS buttononce to advanceto next code.

800TYPE OF DRYER PRICING

800Fixed Cycle with Top Off. For detaileddescription,see General User Information.

8	FC	Fixed Cycle. For detailed description,see GeneralUser
		Information.
		Use DELICATESbuttonto make thisselection.
		PN MODELS: Factory defaultof FC.

￿Press PERM. PRESS buttononce to advanceto next code.

90 0 CYCLE COUNTER OPTION

This option is either SELECTED‘ON’ or NOT SELECTED‘OFF’.

90 0	Not Selected ‘OFF’.
90 C	Selected ‘ON’ and not able to be deselected.Press DELICATES
	button 3 consecutive times to select ‘ON’. Once selected‘ON’
	it cannot be deselected.

￿Press PERM. PRESS buttononce to advanceto next code.

14