Battery Charge Cable Connections | Miller Electric 250 specification

.A complete Parts List is available at www.MillerWelds.com

8-3. Battery Charge Cable Connections

5

4

1

3

−

+

3

2

Ref. 228 649-A / Ref. 804 397-A / S-0714

!Stop engine.

!Do not charge a battery which has loose terminals or one showing damage such as a cracked case or cover.

!Have only qualified persons do bat- tery charging work.

!Keep cables away from moving parts.

!Do not use damaged cables.

!Be sure charger output voltage matches battery voltage.

! Read BCI Battery Service Manual before charging.

.Before connecting to battery, place

Charge Voltage switch in position matching voltage of battery being charged.

1Battery

2Battery Charging Cables

Use less than 20 feet (6.1 m) of AWG #1 or larger cable.

3 Terminal Lug

Use lugs of proper amperage capacity and hole size for connecting to charge output terminals.

Install suitable connectors on remaining ends of battery cables.

4Battery Charge Positive (+) Output Terminal

5Battery Charge Negative (−) Output Terminal

.Connect charging cables to battery charge output terminals before con- necting to battery terminals.

Connect Battery Charge Positive (+) cable to battery positive (+) terminal, and battery Charge Negative (−) cable to battery nega- tive (−) terminal.

OM-217 455 Page 28

Image 32

Miller Electric 250 manual Battery Charge Cable Connections

Contents

OM-217 455H File Engine DriveVisit our website at 2007−05−21 From Miller to You Table of Contents 13-2 13-313-4 13-5 Symbol Usage Arc Welding HazardsElectric Shock can kill HOT Parts can cause severe burns Fumes and Gases can be hazardous Buildup of GAS can injure or killARC Rays can burn eyes and skin Welding can cause fire or explosion Engine Hazards Compressed Air Hazards Welding Wire can cause injury HOT Parts can cause burns and injuryFire or Explosion hazard Falling Unit can cause injury Principal Safety Standards California Proposition 65 WarningsEMF Information Radiation can cause interference Signification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer Indique des instructions spécifiques LE Soudage peut provoquer un in cendie ou une explosion DES Pièces Chaudes peuvent provoquer des brûlures gravesLES Fumées ET LES GAZ peuvent être dangereux DES Organes Mobiles peuvent pro voquer des blessures LE Bruit peut affecter l’ouïe’EXPLOSION DE LA Batterie peu Risque D’INCENDIE OU D’EXPLO- Sion LA Chaleur DU Moteur peut pro- voquer un incendie’AIR Comprimé peut provoquer des blessures LE Surchauffement peut endom- mager le moteur électrique DES Organes Mobiles peuvent provoquer des blessuresLES Fils DE Soudage peuvent provoquer des blessures ’EMPLOI Excessif peut Proposition californienne 65 Avertissements Principales normes de sécuritéInformation EMF En ce qui concerne les implants médicaux − Specifications Symbol DefinitionsWeld, Power, and Engine Specifications − Definitions Dimensions Dimensions, Weights, and Operating AnglesDimensions For Units With Optional Running Gear − Installation Installing Welding GeneratorVehicle frame. Always connect a ground wire Mounting Installing Exhaust Pipe Connecting the Battery+ − Stop engine and let cool Overview And Engine Prestart Checks Engine Left Side Engine Right Side Starting engine for the first timeRun-in period first 100 hours Daily pre-start checks Connecting to Weld Output Terminals Correct InstallationWork Weld Output Terminal Tools Needed Do not place Selecting Weld Cable Sizes Engine Control Switches Place switch in Run position to operate most MIG equipment− Operating the Welding Generator Do not use glow plugs longer than 20 seconds Weld Output Controls Typical Stick Welding Connections And Control Settings Typical Settings For 7018 1/8 ElectrodeStop engine Work Clamp Electrode Holder Typical MIG Welding Connections And Settings Set Weld Process Selector switch to Wire + Dcep positionSet Weld Process Selector switch to Wire + position Set Weld Process Selector switch to Wire − position Dcen Tools Needed 3/4 Work Not Used To Work Left Side View Generator Power Receptacles − Operating Auxiliary EquipmentAt least once a month, run engine at To verify Gfci is working properly Simultaneous Weld And Power Determining Battery Charging Current − Operating Optional Battery ChargerBattery Charge Controls Battery Charge Cable Connections Battery Charging Procedure Minutes Start Your Professional Welding Career Now − Maintenance and Troubleshooting Routine Maintenance Maintenance Label And Engine Maintenance Activities Stop engine and let cool Oil And Fuel 804 197-A / Ref 803 111-A / 227 Cleaner or with dirty element. Engine Ment is not covered by the warrantyAir cleaner primary element can Damage when determining whether Adjusting Engine Speed Adjusting Fuel Solenoid PositionStop screw is factory-set and should not be adjusted Checking Fuel Solenoid Adjusting Throttle Solenoid Checking Throttle Solenoid16 mm Check for non-binding Adjusting Weld/Power Speed Making Engine Speed AdjustmentsAdjusting Idle Speed Overload Protection Component Panel Stop engineFuse F1 Supplementary Protector CB8 Troubleshooting Tables Generator PowerWelding Trouble Remedy Maintenance Display Action Engine − Parts List Recommended Spare PartsRecommended Spare Parts Current transformer CT1, and throttle solenoid TS1 − Electrical Diagrams Circuit Diagram For Welding Generator 228 719-B OM-217 455 231 607-B − RUN-IN and Wetstacking Run-In And Wetstacking − Performance Data Fuel Consumption CurvesUS Gal./Hr Idle Generator Power Curve Duty CycleVolts AC Amperes At 120 Volts AC Amps Stick Mode Volt-Ampere CurvesDC Amps CC/AC Stick Mode AC Volts MIG Mode Volt-Ampere Curve DC Amps Grounding Generator To Truck Or Trailer Frame − Generator Power GuidelinesSelecting Equipment Grounding When Supplying Building Systems How Much Power Does Equipment Require?Use ground device as stated in electrical codes Amperes x Volts = Watts Approximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running Watts Power Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 / Volts = Starting Amperage Typical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible − Stick Welding Smaw Guidelines Stick Welding ProcedureWeld current starts when electrode touches work- piece Striking an Arc − Tapping Technique Electrode and Amperage Selection ChartStriking an Arc − Scratch Start Technique Poor Weld Bead Characteristics Good Weld Bead CharacteristicsPositioning Electrode Holder 10-30 9090 End View of Work Angle Conditions That Affect Weld Bead Shape Electrode Movement During Welding Butt Joints Lap JointTee Joint 16 in 30 1.6 mm Tack Welds Troubleshooting − Porosity Troubleshooting − Excessive SpatterWeld Test Possible Causes Corrective Actions Troubleshooting − Excessive Penetration Troubleshooting − Incomplete FusionTroubleshooting − Lack Of Penetration Troubleshooting − Distortion Troubleshooting − Burn-ThroughTroubleshooting − Waviness Of Bead Work like a Pro Support ServiceYour distributor also gives To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s