Event Type, Snmp Trap Server | Moxa Technologies NPort 5600 guide

NPort 5600 Series User’s ManualConfiguring NPort Administrator

SNMP Trap Server

SNMP trap server IP or domain name

Setting	Factory Default	Necessity
IP or Domain Name	None	Optional

Event Type

Cold start

This refers to starting the system from power off (contrast this with warm start). When performing a cold start, NPort will automatically issue an Auto warning message by e-mail, or send an SNMP trap after booting up.

Warm start

This refers to restarting the computer without turning the power off. When performing a warm start, NPort will automatically send an e-mail, or send an SNMP trap after rebooting.

Authentication failure

The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, NPort will immediately send an e-mail or send an SNMP trap.

IP address changed

The user has changed NPort’s IP address. When the IP address changes, NPort will send an e-mail with the new IP address before NPort reboots. If the NPort is unable to send an e-mail message to the mail server within 15 seconds, NPort will reboot anyway, and abort the e-mail auto warning.

Password changed

The user has changed NPort’s password. When the password changes, NPort will send an e-mail with the password change notice before NPort reboots. If the NPort is unable to send an e-mail message to the mail server within 15 seconds, NPort will reboot anyway, and abort the e-mail auto warning.

5-34

Image 64

Moxa Technologies NPort 5600 user manual Event Type, Snmp Trap Server

Contents

NPort 5600 Series User’s Manual Seventh Edition, July Trademarks Copyright NoticeDisclaimer Table of Contents Chapter IP Serial LIB Page Introduction Product Features Package ChecklistOverview Product Specifications Advanced Built-in Features Software FeaturesPower Requirements Serial Communication Parameters ‰ Panel Layout ‰ Connecting the Hardware Getting Started Rear panel of NPort 5600 series AC Power Rear panel of NPort 5600 series DC PowerPanel Layout Front panel of NPort 5600 series Connecting the Hardware Wiring RequirementsConnecting NPort 5610/30/50-16/8’s Power Connecting NPort 5610-16/8-48V’s Power Connecting to the Network Grounding NPort 5610-16/8-48V Connecting to a Serial Device LED IndicatorsLink Indicator on the Rear Panel of NPort 5650 Fiber Model Adjustable Termination Resistor for the RS-485 Port NPort 5650 DIP Switches Initial IP Address Configuration Factory Default IP Address Default IP addressInitializing NPort’s IP Address LCM Display Button Name Action Detailed Menu Options Level NPort Administration Suite ARP Telnet Console NPort 5600 Series User’s Manual NPort 5600 Series User’s Manual NPort 5600 Series User’s Manual Choosing the Proper Operation Mode Real COM Mode Real COM Mode TCP Server Mode TCP Server Mode UDP Mode TCP Client ModePair Connection Mode Disabled Mode Reverse Telnet ModeRFC2217 Mode PPP Mode Web Console Configuration Opening Your Browser Basic Settings Time Server nameTime zone Local time Network Settings Console IP Configuration IP AddressNetmask Gateway Snmp Settings DNS server 1 / DNS serverCommunity name Contact IP Address Report Auto report to IPAuto report to TCP port Auto report period Serial Settings Port alias Serial Parameters Operating Settings Real COM ModeSetting Factory Default Necessity To 99 min Min Optional TCP alive check time Max connection Setting Factory Default Necessity Required Max. connectionMax connection 2 to Ignore jammed IP Packing length Setting Factory Default Necessity Required DelimiterDelimiter process Force transmit TCP Server Mode Max connection Packing length Setting Factory Default Necessity 4001 Required Command portSetting Factory Default Necessity 966 Optional Local TCP port TCP Client Mode Inactivity time Ignore jammed IP Delimiter process Destination IP address Destination IP address 2/3/4Designated Local Port 1/2/3/4 Connection control Connect/Disconnect Description UDP Mode Force transmit Pair Connection Master Mode Pair Connection ModeSetting Factory Default Necessity To 99 min Min Required Pair Connection Slave Mode Blank Setting Factory Default Necessity To 99 min Optional Reverse Telnet ModeMap CR-LF Disabled Mode RFC2217 Mode Packing length Setting Factory Default Necessity Optional Setting Factory Default Necessity To FF hex None Optional Setting Factory Default Necessity Yes or No Optional PPP ModeTCP/IP compression Accessible IP Settings Source IP addressIP netmask Modem Initial stream Hosts on a specific subnet can access the NPort Any host can access the NPortPPP User Table Allowable Hosts Input format Auto warning E-mail and Snmp Trap Auto Warning SettingsMail Server Event Type Snmp Trap Server Setting Factory Default Necessity Enable, Disable Optional DCD changedDSR changed Mail Monitor Line MonitorMonitor Async Change Password Monitor Async-Settings Load Factory Defaults Configuring NPort Administrator ‰ Overview ‰ Installing NPort Administrator ‰ Configuration Installing NPort Administrator NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB Configuration Broadcast Search Unlock Password Protection NPort 5600 Series User’s Manual IP Serial LIB Lock UnlockBlank Fixed Configuring NPort NPort 5600 Series User’s Manual IP Serial LIB Upgrading Firmware Export/Import Add Target Æ Select target from the list Select Add Target NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB NPort 5600 Series User’s Manual IP Serial LIB Port Monitor COM Mapping On-line COM Mapping NPort 5600 Series User’s Manual IP Serial LIB Fast Flush only flush local buffer NPort 5600 Series User’s Manual IP Serial LIB Off-line COM Mapping IP Location NPort 5600 Series User’s Manual IP Serial LIB IP Serial LIB Why Use IP Serial Library? What is IP Serial Library?How to install IP Serial Library? IP Serial LIB Function Groups Example ProgramServer Control Port Control Input/Output Data Port Status Miscellaneous Pinouts and Cable Wiring ‰ Cable Wiring Diagrams Ethernet Port Pinouts Port Pinout DiagramsSerial Port Pinouts Cable Wiring Diagrams RJ45 8-pins to Female DB9Ethernet Cables Serial Cables for NPort 5610/5650 RS-232 RJ45 8-pins to Male DB9 RJ45 8-pins to Female DB25 Serial Cables for NPort 5630 RS-422/4-wire RS-485 RJ45 8-pins to Female DB25 Serial Cables for NPort 5630 2-wire RS-485 NPort 5600 Series User’s Manual Well Known Port Numbers Serial Cables for NPort 5650 RS-422/4-wire RS-485 Serial Cables for NPort 5650 2-wire RS-485 RJ45 8-pins to Male DB25 Pin Assignments for DB9 and DB25 Connectors Pin Assignments for DB9 Male and Female Connectors Pin Assignments for DB25 Male and Female Connectors TCP Socket Application Service Well Known Port Numbers UDP Socket Application Service Snmp Agent with MIB II & RS-232 Like Group Snmp Agent with MIB II & RS-232 Like Group System MIB Interfaces MIB Address Translation MIB Input Signal Table Output Signal Table Auto IP Report Protocol Auto IP Report Format Info nID List AP ID & Hardware ID Mapping Table Service Information Moxa Internet Services Following services are provided Moxa Product Problem Report FormSerial Number Product Return Procedure