451-0308 | MRV Communications LX-4000 Series manual

Configuring the LX-4000 Series for the First Time

4.Follow the defaults to the end of the install.

5.When your browser connects to the LX, the Java Security Warning window appears.

NOTE: Your Java Security Warning window may vary, depending on your PC operating system.

6.Click on Grant this session. The Java Security Warning window closes. The LX Series Console page reappears, now with the console selection visible.

7.Choosing Encrypted Console means the GUI will run slower, but with security. Choosing Non- Encrypted Console means the GUI will run faster, but without security.

8.Select Encrypted or Non-Encryptedand then select Open Console. A login window appears.

30

MRV Communications, Inc.

www.mrv.com

451-0308

Image 30

MRV Communications LX-4000 Series manual 451-0308

Contents

Corporate Headquarters MRV Americas Service and SupportGetting Started with the LX-4000 Series MRV America Sales MRV International Sales FCC Notice Bsmi Notice Vcci Notice Licensing Notice 451-0308 Table of Contents Appendix C Post Test Error Codes Figures 451-0308 Tables 451-0308 Preface Customer Support Other Documentation Chapter Overview of the LX-4000 Series Conventions System Specifications Description Package Contents Chapter Installing the LX-4000 SeriesHardware Installation Unpack and Inspect the Unit LX-4000 Indicators and Interfaces Front Panel LEDs Rear Panel LEDs Port Status LEDs RCV Link Environmental and Installation Considerations Mbps Mounting the Unit into a 19-inch or 23-inch Rack Connect the Power CableConnecting the Ethernet Interface Cable Connections Connecting Your Management Station Connecting DC PowerConnect Serial Device Cables Powering On Modem Port Optional System Login and Passwords Resetting the Unit Installing the LX-4000 Series Chapter Configuring the LX-4000 Series for the First Time Configuring the LX-4000 Unit for the First TimeFirst Time Quick Configuration 451-0308 Completing the First Time Configuration Assigning an IP Address via the Network Manually Setting the IP Address Via the CLI Accessing and Configuring the Graphical User Interface GUI MRV Communications, Inc 451-0308 Web Configure Mode Web Access Mode Menu/Config Mode GUI EZ Configuration Launching the EZConfig GUI Booting from Defaults Software UpgradesIP Configuration Menu Accessing and Configuring Additional Features Additional Considerations Reinitializing/Powering Off the Unit Command Line Interface CLI Tree StructureAutobauding Feature Additional Considerations for an Internet Environment Sensor Temperature/Humidity Ports Connecting the Temperature/Humidity SensorChapter Alternative Port Capabilities Power Management Async 4-40access sensor Connecting Connecting Power Strip Management Telco Using LX Ports as Alarm Inputs and Control Outputs Alarm Inputs Setup and Usage Control Output Setup and Usage Typical Alarm Inputs Connections Typical Interface Design for Control Output Signals Appendix a Technical Specifications LX-4000 Series Specifications Description LX-4008, LX-4016 Appendix a Technical Specifications Temperature/Humidity Sensor Specifications Description Appendix B Factory Defaults LX-4000 Series Factory Defaults Description Ppciboot Factory Default Settings Main Menu Configuration Factory Default Setting Appendix C Post Test Error Codes Error Code Definitions 451-0308 Post Test Error Code Sample 3 4 5 6 7 Appendix D Cabling the LX-4000 Series Serial Device ConnectorsDiagnostic Port Connector Port Cabling Considerations Ordering Cables 10/100 ConnectorModular Adapters Pin Assignments DB-25 Pins Ordering and Installing the Inlet Connector Lock Connecting to the Diagnostic Port PortModem Control/Hardware Flow Control RJ-45 Wiring Considerations Modular Adapters RJ-45 to DB-25 Supports RTS/CTS MRV 8-Wire Cabling Adapter Wiring, LX-Series to DCE, with Ring MX-151-3027 LX Series Numerics DB-2556, 61 RJ-4561 RJ-45 jacks Index