Appendix B Factory Defaults | MRV Communications LX-4000 Series

Appendix B - Factory Defaults

The following table provides the factory defaults for the LX-4000 Series.

Table 3 - LX-4000 Series Factory Defaults

Item	Description

DIAG Port/local management port (default	The DIAG port (port 0) is the console manage-
settings)	ment port.
	Auto Protocol Detect (APD) is disabled.
	Autobaud is disabled.
	9600/8/1/None.
	Quick Start is enabled.
	Access is Local.
	Flow Control is Xon/Xoff.

All Ports Except Management and Modem	Autobaud is disabled.
Ports (default settings)	9600/8/1/None.
	Access is Remote.
	APD is disabled.
	Flow Control is Xon/Xoff.

Modem Port (default settings)	Autobaud is disabled.
	Speed is 57600.
	Access is Local.
	APD is enabled.
	Flow Control is CTS.

451-0308

MRV Communications, Inc.

www.mrv.com

49

Image 49

MRV Communications manual Appendix B Factory Defaults, LX-4000 Series Factory Defaults Description

Contents

Getting Started with the LX-4000 Series MRV Americas Service and SupportCorporate Headquarters MRV America Sales MRV International Sales FCC Notice Licensing Notice Bsmi Notice Vcci Notice 451-0308 Table of Contents Appendix C Post Test Error Codes Figures 451-0308 Tables 451-0308 Customer Support Preface Other Documentation Conventions Chapter Overview of the LX-4000 Series Description System Specifications Hardware Installation Chapter Installing the LX-4000 SeriesPackage Contents Unpack and Inspect the Unit Front Panel LEDs LX-4000 Indicators and Interfaces Port Status LEDs Rear Panel LEDs RCV Link Mbps Environmental and Installation Considerations Connecting the Ethernet Interface Connect the Power CableMounting the Unit into a 19-inch or 23-inch Rack Cable Connections Connecting DC Power Connecting Your Management StationConnect Serial Device Cables Modem Port Optional Powering On Resetting the Unit System Login and Passwords Installing the LX-4000 Series Configuring the LX-4000 Unit for the First Time Chapter Configuring the LX-4000 Series for the First TimeFirst Time Quick Configuration 451-0308 Assigning an IP Address via the Network Completing the First Time Configuration Accessing and Configuring the Graphical User Interface GUI Manually Setting the IP Address Via the CLI MRV Communications, Inc 451-0308 Web Configure Mode Menu/Config Mode Web Access Mode Launching the EZConfig GUI GUI EZ Configuration IP Configuration Menu Software UpgradesBooting from Defaults Accessing and Configuring Additional Features Additional Considerations Autobauding Feature Command Line Interface CLI Tree StructureReinitializing/Powering Off the Unit Additional Considerations for an Internet Environment Connecting the Temperature/Humidity Sensor Sensor Temperature/Humidity PortsChapter Alternative Port Capabilities Async 4-40access sensor Power Management Connecting Connecting Power Strip Management Telco Alarm Inputs Setup and Usage Using LX Ports as Alarm Inputs and Control Outputs Typical Alarm Inputs Connections Control Output Setup and Usage Typical Interface Design for Control Output Signals LX-4000 Series Specifications Description Appendix a Technical Specifications LX-4008, LX-4016 Appendix a Technical Specifications Temperature/Humidity Sensor Specifications Description LX-4000 Series Factory Defaults Description Appendix B Factory Defaults Main Menu Configuration Factory Default Setting Ppciboot Factory Default Settings Error Code Definitions Appendix C Post Test Error Codes 451-0308 Post Test Error Code Sample 3 4 5 6 7 Diagnostic Port Connector Port Serial Device ConnectorsAppendix D Cabling the LX-4000 Series Cabling Considerations Modular Adapters 10/100 ConnectorOrdering Cables Pin Assignments DB-25 Pins Connecting to the Diagnostic Port Port Ordering and Installing the Inlet Connector LockModem Control/Hardware Flow Control Modular Adapters RJ-45 to DB-25 RJ-45 Wiring Considerations Supports RTS/CTS Adapter Wiring, LX-Series to DCE, with Ring MRV 8-Wire Cabling LX Series MX-151-3027 Numerics DB-2556, 61 RJ-4561 RJ-45 jacks Index