Muratec MFX-3050 manual Troubleshooting

Message	Meaning	Suggested solutions
Invalid Server	The server address	Enter the correct server
Address	you have entered is	address.
	invalid.
Line Busy	The receiving fax	Try again after a few
	machine did not	minutes.
	answer or the line is
	already engaged.
[Line Error]	Your machine	Try again. If the problem
	cannot connect with	persists, wait an hour or
	the receiving fax	so for the line to clear
	machine or has lost	and try again.
	contact because of a	Or, turn the ECM mode
	problem with the
		on. See page 10.1.
	phone line.
Low Heat Error	There is a problem	Unplug the power cord
Cycle Power	in the fuser unit.	and plug it back in. If the
		problem persists, please
		call for service.
LSU Motor Error	A problem has	Unplug the power cord
Cycle Power	occurred in the LSU	and plug it back inches. If
	(Laser Scanning	the problem persists,
	Unit).	please call for service.
LSU Hsync Error	A problem has	Unplug the power cord
Cycle Power	occurred in the LSU	and plug it back inches. If
	(Laser Scanning	the problem persists,
	Unit).	please call for service.
Main Motor	There is a problem	Open and then close the
Locked	in the main motor.	front cover.
Mail Exceeds	The mail size is	Divide your mail or
Server Support	larger than the	reduce the resolution.
	supported size by
	SMTP server.
Memory Full	The memory is full.	Delete unnecessary fax
		jobs and retransmit after
		more memory becomes
		available. Alternatively,
		split the transmission into
		more than one operation.
MP Tray	There is no paper in	Load paper in the multi-
Paper Empty	the multi-purpose	purpose tray. See page
	tray.	5.7.
Network Error	There is a problem	Contact your network
	with the network.	administrator.

Message	Meaning	Suggested solutions
[No Answer]	The receiving fax	Try again. Make sure that
	machine has not	the receiving machine is
	answered after	operational.
	several redial
	attempts.
Not Assigned	The speed button or	Enter the number or
	speed dial number	email address manually
	you tried to use has	using the number keypad
	no number or email	or store the number or
	address assigned to	address.
	it.
[No Paper]	The paper in the tray	Load paper in the tray.
Add Paper	has run out.	See page 5.5.
One Page is	Single page data	Reduce the resolution
Too Large	exceeds the	and try again.
	configured mail size.
Open Heat Error	There is a problem	Unplug the power cord
Cycle Power	in the fuser unit.	and plug it back in. If the
		problem persists, please
		call for service.
Operation Not	You are in the Add	Check the display to see
Assigned	Page/Cancel Job	if there are any
	operation, but there	scheduled jobs.
	are no jobs stored.
Over Heat Error	There is a problem	Unplug the power cord
Cycle Power	in the fuser unit.	and plug it back in. If the
		problem persists, please
		call for service.
Paper Jam 0	Paper has jammed	Clear the jam. See page
Open/Close Door	in the feeding area	14.2 and page 14.3.
	of the tray.
Paper Jam 1	Paper has jammed	Clear the jam. See page
Open/Close Door	in the fuser area.	14.3.
Paper Jam 2	Paper has jammed	Clear the jam. See page
Check Inside	in the paper exit	14.4.
	area.
Power Failure	Power has turned off	The job which you were
	then on and the	trying to do before the
	machine’s memory	power failure must be
	has not been back	completely re-done.
	up.

14.8 <Troubleshooting>