6
THIS GAS APPLIANCE SHOULD BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local codes. Installation practices vary from region to region and it is important to know the specifics that apply to your area, for example in Massachusetts State:
•This product must be installed by a licensed plumber or gas fitter when installed within the commonwealth of Massachusetts.
•The appliance damper must be removed or welded in the open position prior to installation of a appliance insert or gas log.
•The appliance off valve must be a “T” handle gas cock.
•The flexible connector must not be longer than 36 inches.
•A Carbon Monoxide detector is required in all rooms containing gas fired appliances.
•The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed combustion product.
The installation must conform with local codes or, in | We suggest that our gas | |
absence of local codes, the National Gas and Propane | ||
hearth products be installed | ||
Installation Code CSA B149.1 in Canada, or the National | ||
and serviced by professionals | ||
Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United | ||
States. Suitable for mobile home installation if installed in | who are certified in the U.S. | |
accordance with the current standard CAN/CSA Z240MH | by the National Appliance | |
Series, for gas equipped mobile homes, in Canada or | Institute® (NFI) as NFI Gas | |
ANSI Z223.1 and NFPA 54 in the United States. | ||
Specialists | ||
|
As long as the required clearance to combustibles is
www.nficertified.org
maintained, the most desirable and beneficial location for an appliance is in the center of a building, thereby allowing the most efficient use of the heat created. The location of windows, doors and the traffic flow in the room where the appliance is to be located should be considered. If possible, you should choose a location where the vent will pass through the house without cutting a floor or roof joist.
4.1
When the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth.
The appliance, when installed with a blower, must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI/NFPA
2.3GENERAL INFORMATION
FOR YOUR SATISFACTION, THIS APPLIANCE HAS BEEN
AND QUALITY!
| GDS600 | GS600 | ||
| NG | LP | NG | LP |
|
|
|
|
|
Altitude (FT) | ||||
|
|
|
|
|
Max. Input (BTU/HR) | 35,000 (Top vent) | 31,500 (Top vent) | 35, 000 | 31,500 |
| 21, 000 (Rear vent) | 16,380 (Rear vent) |
|
|
Max. Output (BTU/HR) | 27,300 | 24,570 | 27,300 | 24,570 |
|
|
|
|
|
Max. Steady State | 78% | 78% | 78% | 78% |
Efficiency (w/the fan on) |
|
|
|
|
|
|
|
|
|
Max. A.F.U.E. | 72% | 71% | 72% | 71% |
|
|
|
|
|
Min. Inlet Gas Supply | 4.5" Water Column | 11" Water Column | 4.5" Water Column | 11" Water Column |
Pressure |
|
|
|
|
|
|
|
|
|
Max. Inlet Gas Supply | 7" Water Column | 13" Water Column | 7" Water Column | 13" Water Column |
Pressure |
|
|
|
|
|
|
|
|
|
Manifold Pressure (Un- | 3.5" Water Column | 10" Water Column | 3.5" Water Column | 10" Water Column |
der Flow Conditions) |
|
|
|
|
