System Construction, Right-TO-Left Scanning | NCR 7883 instruction

NCR RealScan 7883 Installation and Owner Guide

System Construction

The NCR RealScan 7883, METTLER TOLEDO® Scale, & ScanMaxTMHS system can be constructed for right-to-left scanning or for left-to-right scanning. This is accomplished through the orientation of the Bridge Plate within the scale unit.

Right-TO-Left Scanning

20208

Left-To-Right Scanning

20209

497-0424789 Release F

04/04

41 of 75

Image 41

NCR 7883 manual System Construction, Right-TO-Left Scanning, Left-To-Right Scanning

Contents

Information Products RSD-Atlanta RealScan Installation and Owner Guide Contents Laser Safety Label Laser Module Label Laser Power Revision Record Obtaining Technical Assistance Obtaining Additional Information NCR RealScan 7883 Mountings Step Installation Instructions Standard Interface Connection Installing Power Supply and Interface CablesConnecting the Cables to an NCR RealScan USB Interface Connection IBM HID NCR RealScan 7835/7836 Auxiliary RS-232 Port RealScan 7892 Bi-Modal Presentation Scanner Special InstallationsRS-232 Peripherals RealScan 7837 Programming Programming the RealScanRealScan 7832 Programming Factory Default RS232, 7 DATA, 1 STOP, Space Parity Flash Latest Firmware Programming the RealScan Setting Program Parameters and Verifying Host ConnectionTurning on the RealScan UPC/EAN Programming Defaults Baud Rate IBM Communications Programming for USB ConnectionRS-232 Communications RSS-14 Stacked Reduced Space SymbologyRSS Expanded RSS Expanded Stacked Disabling RSS Making Other Program ChangesEnabling RSS UPC-A Scan Sample Tags 01234 5 678 9 Determining Label Quality Scan Zone Adjusting Screw Setting RealScan 7883 Scan Zone Vertical Pass-by Scanning Horizontal Pass-by Scanning Vertical Presentation Scanning from Bottom Vertical Presentation Scanning from Top Plastic Top Plate Mounting the RealScanRubber Feet Plastic Top Plate ScannerC Latch Clip Mounting Screw Vertical Mounting Bracket Cable Clamps Checkstand CutoutCheckpoint Cable Operating the Scanner Cleaning the Scanner Green Status Tones Problem Indicator Correcting Scanner Problems Then supply again Most Common Interface Cables Interface ConnectorInterface Information Communications Protocol Options 4 and B not supported yet Communications ProtocolProgramming Worksheet Checkstand Hole RealScan 7883 Horizontal Mount Features Ventilation Requirements Checkstand Hole RealScan 7883 Flat Mount Installation Type Input Voltage L1, L2 Circuit Breakers Electrical Wiring NCR Components NCR RealScan Mettler Toledo Scale, & Sensormatic ScanMaxTMHS Sensormatic Components Mettler Toledo Components Left-To-Right Scanning System ConstructionRight-TO-Left Scanning Configuring the Scale Installing the Scanner Connecting Sensormatic Components Routing the Cables Completing the Installation Calibrating the Mettler Toledo Scale NCR RealScan 7883 Installation and Owner Guide Sensormatic Programmable Functions Sensormatic Deactivation Indicators Scale Problems TroubleshootingScanner Problems Sensormatic Deactivation Good Read Tone Programming WorksheetsCommunications Protocol Bar Codes Timers Code Bar Codes Unique Identifier Label Identifiers 21 RS-232 Parameters 20 RS-232 Parameters 24 RS-232 Communications Options 22 RS-232 Prefix Byte23 RS-232 Terminator Byte Miscellaneous Parameters RealScan Ascii Code Chart Identification Labels Regulatory Information NCR Corporation Duluth, Ga CE Mark Applicability Declaration of Conformity Laser Module Label Laser SafetyLaser Safety Label Laser Power Reset Volume AdjustmentDefault Programming Tags End Programming ModeSave and Reset Abort Diagnostic ModeRS-232 Temporary Service Mode Mode Reset Tallies Hex Firmware Flashing R0050 R0053 Hex a Hex D Hex BHex C Hex F Hex E