Nortel Networks 8672A Enabling OSPF routing

132 Chapter 6 Configuring the Passport 8672ATM Module

209195-A

5Click Enable.

6Click Apply.

The IP Address tab is redisplayed.

7Click Close.

Enabling OSPF routing

If the routing protocol is OSPF, to enable OSPF routing:

1From the Device Manager menu bar, choose VLAN > VLANs.

The VLAN dialog box opens with the Basic tab displayed (Figure52 on

page 120).

Table41 on page 120 describes the fields in the VLAN Basic tab.

2Click one of the VLANs.

3Click IP.

Listen Enables or disables RIP reception on the specified

interface.

Poison Enables or disables operation of poison reverse on the

specified interface. If poison is disabled, split-horizon

operation is enabled.

AdvertiseDefaultRoute Indicates whether this interface should advertise a RIP

default route.

AcceptDefaultRoute Indicates whether this interface should accept a RIP

default route.

TriggeredUpdateEnable Indicates whether the RIP triggered update feature should

be enabled on this interface.

AutoAggregateEnable Indicates whether the auto aggregation feature should be

enabled on this interface.

AdvertiseWhenDown Indicates whether vlan state change should be notified to

layer 3 or not, provided the vlan is configured as routable

interface. Also used for single routable ports, in that case

the criteria for state is PortOperStatus.

Table 46 RIP tab fields (continued)

Field Description

Contents

Main 209195-A Copyright 2001 Nortel Networks Trademarks Statement of conditions USA requirements only Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice Page Page Page Page Contents Chapter 4 Managing the Passport 8672ATM Module with Device Manager. . . . . . . . 47 Chapter 5 Managing the Passport 8672ATM Module with the CLI . . . . . . . . . . . . . . . 73 Chapter 6 Configuring the Passport 8672ATM Module . . . . . . . . . . . . . . . . . . . . . . . 115 Page Figures Page Page Page Tab le s Page Preface Before you begin Text conventions Page Related publications Page How to get help Chapter 1 About the Passport 8672ATM Module Features ATM ELANs, and Ethernet VLANs Virtual network router Traffic shaping RFC 1483 Support Physical description Media dependent adapters Online LED MDA LEDs Console and Diag ports Page Chapter 2 Passport 8672ATM Module technology overview ATM terms and acronyms Page SONET terms and acronyms SONET transmission rates Chapter 3 Installing the Passport 8672ATM Module Safety and environmental precautions Page Installing the Passport 8672ATM Module . Page Verifying installation Initialization Page 42 Chapter 3 Installing the Passport 8672ATM Module Figure 10 Unsuccessful download screen output ******************************** MDA insertion and configuration Replacing a module Starting the system after a module replacement Starting the system with an empty slot Page Chapter 4 Managing the Passport 8672ATM Module with Device Manager Port numbering Device Manager Device Manager access and passwords Installing Device Manager Page Configuring ATM using Device Manager Page Chapter 4 Managing the Passport 8672ATM Module with Device Manager 53 Table 5 Interface tab items Resetting the module Page 3Click the ATM tab. The ATM tab opens (Figure14). Viewing MDA information Enabling or disabling a port Editing port parameters Editing ATM and framing parameters Table 9 describes the items in the ATM tab. Editing circuit parameters Table 1 0 describes the fields in the ATM PVC tab. 4Click Insert. The Insert ATM PVC dialog box opens (Figure18). Table 1 1 describes the fields in the Insert ATM PVC dialog box. 5In the Vpi field, type the VPI-bit size (an integer between 0 and 255). Deleting a PVC Configuring ATM 1483 ELAN parameters Table 1 2 describes the fields in the ATM 1483 ELAN tab. 4Click Insert. The Insert ATM 1483 ELAN dialog box opens (Figure 22). Page Page Deleting an ATM 1483 ELAN Page Page Chapter 5 Managing the Passport 8672ATM Module with the CLI Command line interface Configuration commands Module commands 1483 ELAN statistics config atmcard elan-stats clear atm elan-stats <vlan id> show atm elan-stats <vlan id> clear atm elan-stats Port commands 78 Chapter 5 Managing the Passport 8672ATM Module with the CLI config atm command Table 1 6 describes the parameters and variables for the config atm <ports> Tabl e 16 con fig atm command parameters and variables Chapter 5 Managing the Passport 8672ATM Module with the CLI 79 config atm pvc command Table 1 7 describes the parameters and vari ables for the config atm pvc Tabl e 16 con fig atm command parameters and variables (continued) 80 Chapter 5 Managing the Passport 8672ATM Module with the CLI config atm pvc 1483 command config atm <ports> pvc 1483 ip config atm <ports> pvc 1483 ipx Table 1 8 describes the parameters and v ariables for the config atm <ports> pvc 1483 command. Tabl e 18 con fig atm pvc 1483 bridged command parameters and variables Table 1 9 describes the parameters and vari ables for the config atm pvc 1483 ip command. config atm info command Figure 27 shows a sample of the output resulting from executing the config atm Show commands show ports info atm all command Chapter 5 Managing the Passport 8672ATM Module with the CLI 83 Figure 28 show ports info atm all command output 84 Chapter 5 Managing the Passport 8672ATM Module with the CLI Table 2 1 describes the information fields for the show ports info atm all command. Table 21 Information fields for the s how ports info atm all command Chapter 5 Managing the Passport 8672ATM Module with the CLI 85 Figure 29 show ports info atm ports command output show ports info atm ports command show ports info atm ports Table 21 Information fields for the s how ports info atm all command (continued) 86 Chapter 5 Managing the Passport 8672ATM Module with the CLI Table 2 2 describes the information fields for the show ports info atm ports command. Table 22 Information fields for the s how ports info atm ports command Chapter 5 Managing the Passport 8672ATM Module with the CLI 87 show ports info atm pvc command show ports info atm pvc [<ports>] Figure 30 show ports info atm pvc command output Table 2 3 describes the information fields for the show ports info atm pvc command. Table 23 Information fields for the s how ports info atm pvc command show ports info atm 1483 command Table 2 4 describes the information fields for the show ports info atm 1483 command. show ports stats atmport command This command displays statistics for atm ports (Figure 32). The command uses the syntax: 90 Chapter 5 Managing the Passport 8672ATM Module with the CLI Figure 32 show ports stats atmport [<port num>] command output Table 2 5 describes the information fields for the show ports stats atmport command. Table 25 Information fields for the show ports stats atmport command show ports stats atm felinecurrent Figure 33 shows sample output for the show ports stats atm 92 Chapter 5 Managing the Passport 8672ATM Module with the CLI Figure 33 show ports stats atm felinecurrent command output Table 2 6 describes the information fields for the show ports stats atm show ports stats atm felineinterval Table 2 7 describes the information fields for the show ports stats atm 94 Chapter 5 Managing the Passport 8672ATM Module with the CLI show ports stats atm fepathcurrent Table 27 Information fields for the show ports stats atm felineinterval Table 2 8 describes the information fields for the show ports stats atm show ports stats atm fepathinterval 96 Chapter 5 Managing the Passport 8672ATM Module with the CLI Figure 36 show ports stats atm fepathinterval command output Table 2 9 describes the information fields for the show ports stats atm show ports stats atm linecurrent This command displays current st atistics (Figure 37) for the line. The command uses the syntax: Table 3 0 describes the information fields for the show ports stats atm 98 Chapter 5 Managing the Passport 8672ATM Module with the CLI show ports stats atm lineinterval Table 30 Information fields for the s how ports stats atm linecurrent Table 3 1 describes the information fields for the show ports stats atm show ports stats atm pathcurrent 100 Chapter 5 Managing the Passport 8672ATM Module with the CLI Figure 39 show ports stats atm pathcurrent command output Table 3 2 describes the information fields for the show ports stats atm show ports stats atm pathinterval Table 3 3 describes the information fields for the show ports stats atm 102 Chapter 5 Managing the Passport 8672ATM Module with the CLI show ports stats atm sectioncurrent Table 33 Information fields for the show ports stats atm pathinterval Table 3 4 describes the information fields for the show ports stats atm show ports stats atm sectioninterval 104 Chapter 5 Managing the Passport 8672ATM Module with the CLI Figure 42 show ports stats atm sectioninterval command output Table 3 5 describes the information fields for the show ports stats atm show ports stats atm sonetmediumtbl This command displays statistics (Figure43) on the SONET medium. The command uses the syntax: Table 3 6 describes the information fields f or the show ports stats atm sonetmediumtbl command. Web management ATM folder Table 3 7 describes the fields displayed in the System page. 108 Chapter 5 Managing the Passport 8672ATM Module with the CLI Table 37 System page fields (continue d) Page Table 3 8 describes the fields displayed in th e PVC page. Page 112 Chapter 5 Managing the Passport 8672ATM Module with the CLI Table 3 9 describes the fields displayed in the 1483 ELAN page. To view the current port parameters, in the ATM menu, click Port. The Port page opens (Figure49). Table 39 1483 ELAN page items Table 4 0 describes the fields displayed in th e Port page. 114 Chapter 5 Managing the Passport 8672ATM Module with the CLI Table 40 Port page items (continued) Chapter 6 Configuring the Passport 8672ATM Module Initial configuration Changing the clock setting using Device Manager Changing the clock setting using the CLI Basic configuration procedures Bridging point-to-point traffic using an ATM 1483 PVC using Device Manager Creating a VLAN byPort and adding ports Table 4 1 describes the Basic tab fields. Page Page Configuring an ATM 1483 PVC Associating the PVC with the VLAN Bridging point-to-point traffic using an ATM 1483 PVC using the CLI config vlan 2 create byport 1 config vlan 2 port add 1/1, 3/40-3/48 config atm 1/1 pvc create 0.100 enc 1483-null serv ubr config atm 1/1 pvc create 0.100 enc 1483-null serv vbr<PCR value>scr<SCR value> mbs<MBS value> Bridging point-to-multipoint traffic using an ATM 1483 PVC using Device Manager Configuring two ATM 1483 PVCs on the same ATM port Associating the PVCs with the same VLAN Bridging point-to-multipoint traffic using an ATM 1483 PVC using the CLI Configuring an IP routing 1483 PVC using Device Manager Creating two VLANs byPort Assigning IP addresses Page Enabling RIP routing Enabling OSPF routing Page Configuring a null-encapsulation PVC Associating the PVC with the VLAN Configuring an IP routing 1483 PVC using the CLI Configuring an IPX routing 1483 PVC using Device Manager Creating two VLANs byPort Configuring IPX network numbers Page Enabling IPX forwarding Enabling IPX network number forwarding Configuring a null-encapsulation PVC Associating the PVC with the VLAN Configuring an IPX routing 1483 PVC using the CLI Page Appendix A Technical Specifications This appendix lists the technical specifications for the Passport 8672ATM Module. Page Appendix B Factory defaults Page Index A C D E F G H L M N O P R S T U V W