Manuals / Omega Engineering / Personal Care / Thermometer

Omega Engineering OS534 System Requirements, After all data is taken, press the key again and

Models: OS524

1 78

Download 78 pages 980 b

Page 35

7.After all data is taken, press the key again and

2Using the Handheld Infrared Thermometer

PRN °F

7.After all data is taken, press the key again and

the. icon disappears.

8.Press and hold the until the Emissivity display Mode

(E) appears.

9.Press the key to unlock the trigger.

2.3.10Sending Temperature Data to a Personal Computer (OS533, OS534, OS523, OS524)

PRN °F

The thermometer can transmit temperature data to a Personal Computer via the RS-232 phone jack and the RS-232 cable.

NOTE

Bottom hole is

the RS-232 jack

Personal

Computer

RS-232

Digital

Cable

6-pin	25-pin 'D'
Phone Jack	Connector
Phone Jack
To the	To the
Thermometer	Computer

Figure 2-15. Personal Computer Hookup

2.3.10.1Software Installation

System Requirements

To run IR_TEMPSOFT you must have an IBM-compatible personal computer with these minimum specifications:

2-20

Image 35

Contents

Shop online at User’s GuideOS531, OS532, OS53x-CF OS533, OS534, OS530L, OS530HR OS523, OS524 OMEGASCOPE Handheld Infrared ThermometerFor immediate technical or application assistance OMEGAnet Online Service omega.comInternet e-mail info@omega.com Servicing North AmericaUnpacking Instructions e-mail info@omega.com AccessoriesModel No DescriptionPage TABLE OF CONTENTSOS530/OS520 Series Handheld Infrared ThermometerTABLE OF CONTENTS 1.1 Introduction General DescriptionThe thermometer is easy to use General Description Display ResolutionOS523 provides three field of views FeaturesOS523 OS524General Description 1.2 Parts of the Thermometer1.2.1 Front of the Thermometer 1 General Description Table 1-2. Display DetailsGeneral Description 1.2.2 Rear of the ThermometerFigure 1-3. OS530 Series Handheld Infrared Thermometer Rear View 1 General Description 2.1.2 ac Power Operation Using the Handheld Infrared Thermometer2.1 How to Power the Thermometer 2.1.1 Battery Operation2.2 Operating the Thermometer Figure 2-5 Field of View OS533, OS530HR Using the Handheld Infrared ThermometerMeasurement distance is from the outside surface of the rubber boot Figure 2-4. Field of View OS531, OS532, OS530LDISTANCE SENSOR LENS TO OBJECT in 2 Using the Handheld Infrared ThermometerFigure 2-6 Field of View OS534, OS523-1 Figure 2-7 Field of View OS53x-CFSPOT Using the Handheld Infrared ThermometerFigure 2-8 Field of View OS523-2 Figure 2-9 Field of View OS523-33. The target temperature and emissivity are displayed on the LCD 2.2.1 Measurement Techniques 2. Pull the trigger and press the key to lock the trigger Using the Handheld Infrared Thermometer 2.3 Real Time Mode Active OperationFigure 2-12. General Operational Block Diagram Handheld Infrared Thermometer Recall ModeUsing MODE DISPLAY Figure 2-13. Visual Function Flow ChartUsekey to change temperature from F to C or vice versa Using the Handheld Infrared ThermometerThis function electronically locks the trigger mechanism 2.3.1 Adjusting Emissivity2.3.2 Using the LOCK Function Refer to Appendices B and C for information on emissivityEvery time the thermometer goes from the sleep mode to the 2.3.3 Calculating Temperature Values2.3.4 Changing the Temperature from F to C or vice versa 2.3.5 Turning on the Display BacklightingTo Determine an unknown target emissivity 2.3.6 Thermocouple Input OS532, OS533, OS534If the temperature exceeds the high alarm setpoint 2.3.7 Using the Alarm FunctionsThe thermometer provides audible and visible alarm indications To set the high alarm valuesetpoint, you will hear a beep and the icon on the display flashes To set the low alarm value OS533, OS534, OS523, OS524If the temperature drops below the low alarm The target has a low emissivity To set and activate the Ambient Target Temperature Compensation Mode8. Press and hold the key until the Emissivity Display Mode E appears 3. Pull the trigger and press the key to lock the the. icon disappears System Requirements8. Press and hold the until the Emissivity display Mode E appears 7. After all data is taken, press the key again andPlease follow this installation procedure to install IRTEMPSOFT program please contact technical support at Omega Engineering Inc waiting for the thermometer to transmit data through your RS-232 port 2.3.11 Storing the Temperature Data on Command OS534, OS523, OS524 1. Pull the trigger and press the key. The icon will appear Figure 2-16. General Operational Block Diagram 2.4 Recall Mode Passive OperationMode Active Recall ModeDisplay stored Recall ModeTable 2-2. Functional Flow Chart Recall Mode 2.4.1 Reviewing the Last Parameters 5. The “Stored Data Points” window will appear 2. Press the key to increment the memory location or Refer to the inside back cover for product warning label Laser Sighting3.1 Warnings and Cautions 3.2 Description The visibility of the laser beam depends on the ambient light levels 3.3 Operating the Laser SightingFigure 3-4 Lines of Sight of the Laser Sighting and Thermometer Sighting Scope 4.1 Sighting Scope 4.2 Installing and Operating the Sighting Scope1 11/16 42.8 mm Figure 4-1. Installing the Sighting Scope4 Sighting Scope Pair of Mounting ClampsSafety Warning Maintenance 5.1 Replacing the Batteries1. Blow off loose particles, using clean air 5.2 Cleaning the Lens5.3 Calibrating the Thermometer 5.4 Servicing the Laser SightingSolution Troubleshooting GuideProblem The thermometer is ProblemTroubleshooting Guide ProblemSolution The temperature reading isSolution ProblemSolution ProblemSpecifications are for all models except where noted SpecificationsTHERMOMETER 7 Specifications With LCD backlighting and SpecificationsComplies with 21 CFR Chapter 1, Subchapter J LASER SIGHTINGGlossary of Key Strokes 8 Glossary of Key Strokes Appendix How Infrared Thermometry Works A Thermal RadiationA Appendix How Infrared Thermometry Works BlackbodySpectral Distribution λ m = T Calculating TemperatureFigure A-3. Field of View of a Thermometer Optics Field of ViewEmissivity ε METALSAppendix Emissivity Values MaterialAppendix Emissivity Values NONMETALSMaterial Emissivity εMethod Appendix Determining an Unknown EmissivityMethod Method 1. Use this method to measure objects at temperatures below 500F 260CAppendix - Determining an Unknown Emissivity C MethodMethod Figure C-2. Determining Emissivity with a Drilled HoleC Appendix Determining an Unknown Emissivity Index Page Page CAUTION OMEGASCOPE WARRANTY/DISCLAIMERRETURN REQUESTS / INQUIRIES pH/CONDUCTIVITY TEMPERATUREPRESSURE, STRAIN AND FORCE FLOW/LEVEL