Omega Vehicle Security 1400 manual Command Summary

API CommandsAppendix A

Command Summary

	Command	Syntax	Description
@	Trigger On Command	@	Trigger on receipt of an @.
*B	Flush Acquisition	*B	Flush any data currently in the acquisition buffer.
	Buffer
*C	Clear Channel	*C	Clear out the channel configuration so that no channels are
	Configuration		configured.
*F	Restore Factory	*F	Restore unit to factory configuration.
	Settings
*K	Change Calibration	*Kkey	Change the calibration keyword, where key is the keyword in the
	Keyword		form of a 5-digit number nnnnn. Therefore the password can
			be no longer than 5 characters.
*P	Adjust Calibration Card	*Pchan	Select voltage level to be enabled for adjustment. Valid options
	Pots		for chan are: 01 - Enable -4.4 Volt Source on calibration card,
			02 - Enable +4.4. Volt Source on calibration card, and 03 -
			Select 0 Volts GND.
*R	Power-On Reset	*R	Power-on reset. Equivalent to hardware reset.
*S	Power-Up Settings	*Smode	Specify power-up configuration mode. Valid options for mode are:
			0 - Power-up under last known configuration (default), and 1 -
			Power-up under factory default configuration.
*T	Time Stamping	*Tstate	Specify whether or not time stamping will be enabled. Valid
			options for state are: 0 - Disable time stamping (default), 1 -
			Enable absolute time stamping, and 2 - Enable relative time
			stamping
A	Assign Alarm Output	Achans,	Set alarm condition where chans is the channel(s) to assign to
		output	the digital output.
			chans may be in two forms: chan (for a single channel where 1
			< chan < max) or first-last(for a range of channels
			where 1< first < last < max),
			where max = 128 for ChartScan/1400.
			output is the digital output number to associate the channel(s)
			with, where 0 < output < 32.
		A?	Query channels assigned to digital output.

A#

Alarm Stamping

A#state

Specify whether or not alarm stamping will be enabled. Valid options for state are: 0 - Disable alarm stamping (default), and 1 - Enable alarm stamping.

C	Configure Channels	Cchans,	Configure the channels for the master unit and its slave units.
		type [,	chans and type are required arguments, while lowsp,
		[lowsp],	highsp and hyst are optional.
		[highsp],	chans may be in two forms: chan (for a single channel where 1
		[hyst] ]
			< chan < max) or first-last(for a range of channels
			where 1 < first < last < max),
			where max = 128 for ChartScan/1400.
			The chassis is chan = 0.
			type is the type to assign to those channels.
		C?	Query current channel configuration.

C#

Select Card

C#card

Select the card from which subsequent QC? and U12 interrogation will retrieve information.

Without optional Relay Card

Valid options for card are: 0 - Selects the chassis; 1, 2, 3, or 4 - Selects the card in corresponding slot of the main unit (with 1 being the bottom slot); and 5, 6, 7, or 8 - Selects the corresponding slot on the expansion chassis (with slot 5 being the bottom slot of the expansion chassis.

With optional Relay Card (installs in slot 1)

Valid options for card are: 0 - Selects the chassis; 1 selects card in slot 2, 2 selects card in slot 3; and so on, with 7 selecting the card in slot 8; and no card 8 available.

A-6 ChartScan User’s Manual