1.Ensure the main unit is powered “OFF,” and has no power sources connected to it.

2.If a signal conditioning card is in slot #1 of the chassis, remove the card.

3.Install Calibration Card into Slot #1 (bottom slot) of the main unit.

CAUTION

Do not perform calibration until after the main unit and calibration equipment have been powered on for at least one hour.

4.With all covers in place, allow the main unit and calibration equipment to warm up (powered on) for at least 1 hour.

5.Place the Calibration Enable/Disable Pushbutton (on main unit rear-panel) in the “enable” (indent) position to enable writing to RAM.

Note to ChartScan users: Early production ChartScan units do not have a Calibration Enable/Disable Pushbutton. For these units the calibration mode is enabled by positioning the DIP switch right-most micro-switch (#9) to the “1” (up) position. Note that ChartScan units with the pushbutton have it located on the rear panel, as indicated in the NetScan figure (page 6-2).

6.If the calibration password has not been changed, enter K12345. If the password has been changed, enter the K command and new password. This enables the calibration mode.

7.Type U2X to verify calibration mode. U128 should appear, indicating the unit is in calibration mode.

8.Insert banana plugs of shorting option (shorting bar or 3 linked plugs) into -V, +V, and GND binding posts of calibration card. This short circuits the analog backplane HI and LO voltage inputs and GND (see previous figure, Calibration Card and Two Shorting Options).

9.Type H0X. The Trigger LED will flash, indicating that offset calibration is in progress. When flashing stops, the chassis offset calibration is complete.

10.Type U2X. U128 should appear, indicating the unit is in calibration mode and that no error has occurred.

Response codes and meanings applicable to calibration are as follows:

Response to U2X

Indication for Calibration Mode

U128

No error

U129

Read Failure (EEPROM Error)

U130

Write Failure (EEPROM Error)

U132

Chksum Err (EEPROM Error)

U136

Cal Err (offset, gain, or temperature

 

sensor out of range)

U144

Invalid password

U160

Invalid command

ChartScan User’s Manual

Calibration 6-7

Page 110 Page 112
Page 111
Image 111
Omega Vehicle Security 1400 manual U128, U129, U130, U132, U136, U144, U160
Page 110 Page 112

1400 specifications

The Omega Vehicle Security 1400 stands out as a premier solution for vehicle protection, offering a blend of advanced technology and user-friendly features. With the increasing rise of vehicle thefts, incorporating a robust security system has become essential for vehicle owners. The Omega 1400 aims to address these concerns effectively, ensuring peace of mind for users.

One of the key features of the Omega Vehicle Security 1400 is its sophisticated alarm system. The device is equipped with a motion sensor that activates the alarm when unauthorized movement is detected. This feature provides an added layer of protection, alerting owners to potential threats even when they are away from their vehicles. Additionally, the system comes with multiple sensors that monitor doors and trunk openings, fortifying security against tampering.

A standout component of the Omega 1400 is its remote control functionality, which allows users to arm and disarm the alarm with ease. Featuring a user-friendly remote, drivers can secure their vehicles from a distance, ensuring convenience and accessibility. The remote not only operates the alarm system but also integrates a panic button, which can be used in emergency situations to deter potential threats.

The Omega Vehicle Security 1400 is also designed with cutting-edge technology, offering compatibility with smartphone applications. This innovation enables users to monitor their vehicles in real-time, providing alerts directly to their mobile devices. Users can check the status of their vehicle, adjust settings, and receive notifications if the alarm is triggered, ensuring they are always connected to their vehicle's security.

Another remarkable characteristic of the Omega 1400 is its built-in GPS tracking capability. In the unfortunate event of a theft, the GPS feature allows vehicle owners to track the location of their vehicle, increasing the chances of recovery. This technology proves invaluable for users who prioritize the safety of their assets.

Additionally, the Omega Vehicle Security 1400 supports a robust battery backup system. This ensures that the alarm remains functional even if the vehicle's power supply is compromised. The reliability and durability of this security system make it a worthy investment for anyone looking to safeguard their vehicle.

In summary, the Omega Vehicle Security 1400 brings together advanced alarm technologies, remote access, GPS tracking, and reliable power support, creating a comprehensive security solution tailored for modern vehicle owners. Each feature has been designed with user convenience and vehicle protection in mind, making it a top choice in the vehicle security landscape.
Top Page Image Contents