Before using this unit
Setting the voltage selector (Worldwide models only)
Worldwide models are equipped with a voltage selector so that you can set your
Determine the proper voltage for your area:
DIGITAL | PRE OUT | ANTENNA | AUDIO | VIDEO | S VIDEO | COMPONENT | FRONT SPEAKERS | SURR SPEAKERS |
| |||
INPUT | R | L |
|
|
| VIDEO | MODEL NO. | |||||
COAX | FRONT |
|
|
|
| MONITOR | OUTPUT | R | L | R | L | |
1 |
|
|
|
|
| OUT | Y |
|
|
|
|
|
| R | L |
|
|
|
|
|
|
|
|
| SUB |
| CENTER |
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
|
| AM | OUT | ZONE 2 | P |
|
|
|
|
|
|
| SURR |
|
|
|
|
|
|
| NETWORK |
|
|
|
|
|
3 |
|
|
|
|
| IN | DVD | P |
|
|
|
|
|
|
| SURR | R | L |
|
|
|
|
|
|
|
|
|
|
|
OPT | BACK/ |
|
|
|
| INPUT 1 |
|
|
|
|
|
| ||
1 | ZONE 2 |
|
|
| FM | OUT |
| Y |
|
|
|
|
|
|
|
|
|
| 75 |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| VIDEO 1 |
| CAUTION: |
|
|
|
|
|
| FRONT |
| MULTI CH |
|
|
|
|
|
|
|
|
| ||
2 |
|
| INPUT | AUDIO |
| IN |
| P | SPEAKER |
|
|
|
|
|
| R |
| L | R | L |
|
|
| VOLTAGE |
|
|
| ||
3 | SUB |
| CENTER |
| PHONO | OUT |
| P | 6 OHMS MIN. |
|
|
| AC OUTLETS |
|
|
|
|
|
| /SPEAKER |
|
|
|
| |||||
|
|
|
|
|
|
| VIDEO 2 |
| SEE |
|
|
| AC | VOLTAGE |
| SURR |
|
|
|
|
|
| INPUT 2 | INSTRUCTIONSELECTORR SURR BACK/ | L | TOTAL 100W MAX. | SELECTOR | ||
4 |
|
|
|
| CD | IN |
| Y | MANUAL FOR | CENTER SPEAKER | ZONE 2 SPEAKERS | AC INLET | 120V | |
|
|
|
|
|
|
|
|
| CORRECT | I R | 12V TRIGGER OUT |
| ||
OPT |
| R | L |
| OUT |
|
|
| SETTINGS. | IN | ZONE 2 |
|
|
|
1 | SURR |
|
|
|
| IN | VIDEO 3 | P |
| RS232 |
|
|
| |
| BACK |
|
|
| TAPE |
|
|
|
| OUT |
|
|
|
|
|
|
|
|
|
|
| 120V | REMOTE |
2 |
|
|
| IN | VIDEO 4 | P | CONTROL | |
GND |
|
| IN | L |
|
|
| |
R | L | R | VIDEO |
|
| |||
DIGITAL |
| AUDIO |
| AUDIO | S VIDEO |
|
| |
OUTPUT |
|
|
|
|
|
|
|
|
Installing the remote controller batteries
1.Remove the battery compartment cover by pressing it and sliding it in the direction shown by the arrow below.
2.Insert two AA (R6 or
3.After the batteries are installed and seated correctly, replace the compartment cover.
1 | 2 | 3 |
Connecting the power cord
(Other than North American and Australian models)
Plug the supplied power cord into this AC INLET.
• Do not use a power cord other than the one supplied with the TX- |
NR900/900E. The power cord supplied is designed for use with |
the |
device. |
• Never have the power cord disconnected from the |
900E while the other end is plugged into the wall outlet. Doing |
so may cause an electric shock. Always connect by plugging into |
the wall outlet last and disconnect by unplugging from the wall |
Notes:
•Do not mix new batteries with old batteries or different kinds of batteries.
•To avoid corrosion, remove the batteries if the remote controller will not be used for a long time.
•Remove dead batteries immediately to avoid damage from corrosion. If the remote controller does not operate smoothly, remove the old batteries and replace them both with two new AA batteries.
Using the remote controller
Point the remote controller toward the remote control sensor. The STANDBY indicator lights up when the unit receives a signal from the remote controller.
outlet first. |
AC INLET
Remote control sensor
STANDBY indicator
Power cord (supplied)
DO NOT connect the power cord at this time.
30˚
30˚
Approx. 16 feet (5 meters)
SEND/LEARN indicator
Notes:
•Make sure that the remote control sensor is not subject to strong light such as direct sunlight or inverted fluorescent light for it may prevent proper operation of the remote controller.
•Using another remote controller in the same room or using the
•Do not put objects on the remote controller. Its buttons may be pressed by mistake and drain the batteries.
•Make sure the audio rack doors do not have colored glass. Placing the
•If there is any obstacle between the remote controller and the remote control sensor, the remote controller will not operate.
7