Enjoying music or videos with the
DIRECT/PURE AUDIO |
| Input source buttons | MASTER VOLUME |
| ||||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| MASTER VOLUME | VOL |
STANDBY/ON |
|
|
|
|
|
|
| |
STANDBY |
|
|
|
|
|
|
| |
POWER |
|
|
|
|
|
| AUDIO SEL |
|
ON OFF | AUDIO REC ( RED ) DVD VIDEO 1 | VIDEO 2 | VIDEO 3 | VIDEO 4 VIDEO 5 | TAPE TUNER | PHONO C D NET AUDIO |
| |
| ZONE 2 (GRN ) |
|
|
|
|
|
|
|
PURE AUDIO UPSAMPLING | SELECTOR |
|
|
|
| DISPLAY |
|
|
| VCR 1 | VCR 2 |
|
|
|
|
|
|
PHONES | REC OUT ZONE 2 OFF STEREO SURROUND |
|
| RT/PTY/TP MEMORY FM MODE SETUP |
| VIDEO 5 INPUT |
|
|
THX | DSP | ENTER | RETURN |
|
| |||
ZONE 2 LEVEL |
|
|
| CLEAR | TUNING | PRESET |
|
|
|
|
|
|
|
| DIGITAL S VIDEO VIDEO | L AUDIO R |
|
AUDIO SELECTOR |
|
|
| PURE A | DIRECT | |||
|
|
|
|
|
Changing the audio mode
Press the AUDIO SELECTOR button on the front panel (or AUDIO SEL button on the remote controller) to change the audio mode. Each time the button is pressed, the mode changes from “Auto” → “Multich” → “Analog” and back to “Auto.” The “Auto” audio mode is recommended for normal circumstances.
Remote controller |
AUDIO
SELECTOR
Auto (automatic detection): With this setting, the
Multich (Multichannel): Select this setting to play back the input from the component connected to the MULTI CHANNEL INPUT port. This setting only appears if “Yes” is selected for the Multichannel setting at Setup Menu → Input Setup Menu → Multichannel Setup
Analog: Select this setting to play back the input from a source component connected to analog audio input jacks. With this setting, even if a digital signal is input from the same component, only the analog signal will be output.
Enjoying the multichannel output
Before starting operations, first make sure that the multichannel connection is properly made and that “Yes” is selected for the Multichannel setting at Setup Menu → Input Setup Menu → Multichannel Setup
1.Press the input source button for the component connected to the MULTI CHANNEL INPUT on the rear of the
2.Select “Multich” using the AUDIO SELECTOR button on the front panel (or AUDIO SEL button on the remote controller).
3.Turn on the connected component and start playing the desired media.
4.If necessary, adjust the output level of each speaker as desired (see page 34).
Adjust the volume at each speaker so that all the volumes sound at the same level at the listening position. For the front right, front left, center, surround right, surround left, surround back right, and surround back left speakers, the output levels can be adjusted between
Note:
If you change the speaker levels in step 4 above, these new levels for multichannel sources will have no effect on the settings at Setup Menu → Speaker Setup Menu → Level Calibration
5.Adjust the volume with the MASTER VOLUME dial (or
the VOL buttons on the remote controller.)
Remote controller | |
MASTER VOLUME |
|
Changing the listening mode:
Each time you press the DIRECT/PURE AUDIO button on the front
panel, the display changes between “Direct” “Pure Audio.” When using a remote controller, press PURE A or DIRECT.
Remote controller |
Using the tone control:
1.Press the SURROUND button on the front panel (or the SURR button on the remote controller) to display “Tone On.”
Remote controller | 2. Adjust the tone at Setup Menu → Audio Adjust Menu | |||
→ Tone Control | ||||
AUDIO |
|
| ||
SELECTOR |
|
|
|
Press the DIRECT/PURE AUDIO button on the front panel (or the DIRECT button on the remote controller) to turn off the tone control.
35