Connecting to Audio/Video equipment
Connecting a DVD Player with
: Signal flow
DIGITAL |
| PR | AUDIO | VIDEO | S VIDEO | COMPONENT |
INPUT |
| RENNA |
|
|
| VIDEO |
COAX | FRONT |
|
|
| MONITOR | OUTPUT |
1 |
|
|
|
| OUT | Y |
|
|
| R | L |
|
|
| SUB |
|
|
|
|
|
2 |
|
| AM | OUT | ZONE 2 | PB |
|
|
| ||||
| SURR |
|
|
|
|
|
3 |
|
|
| IN | DVD | PR |
| SURR | R |
|
|
|
|
OPT | BACK/ |
|
|
| INPUT 1 | |
ZONE 2 |
|
|
|
| ||
|
| FM |
|
|
| |
1 |
|
| OUT |
| Y | |
|
| 75 |
| |||
|
|
|
|
|
| |
|
|
|
|
| VIDEO 1 |
|
2 | FRONT |
|
| IN |
| PB |
| DIO |
|
| |||
| R |
|
|
|
| |
| L |
|
|
|
| |
| SUB |
|
|
|
| |
|
|
|
|
|
| |
3 |
|
| PHONO | OUT |
| PR |
| SURR |
|
|
| VIDEO 2 | INPUT 2 |
|
|
|
|
| ||
4 |
|
| CD | IN |
| Y |
OPT |
| R | OUT |
|
|
|
|
|
|
|
| ||
1 | SURR |
|
| IN | VIDEO 3 | PB |
|
|
|
|
|
| |
| BACK |
| TAPE |
|
|
|
|
|
|
|
|
| |
2 |
|
|
| IN | VIDEO 4 | PR |
| GND |
| IN | L |
|
|
| L | R |
|
| ||
DIGITAL |
| DIO | AUDIO | VIDEO | S VIDEO |
|
OUTPUT |
|
|
|
|
|
|
Digital audio output (coaxial)
R (red) |
Analog audio output |
L (white) |
Video output |
S Video output |
4. DVD player (DVD)
Y
PB
PR
Component video output
Connecting your video components
Below is an example of how you can connect your video components to the
COMPONENT VIDEO INPUT/OUTPUT
For DVD players or other devices that have component video connectors, the
VIDEO IN/OUT
These are the video inputs and outputs. On the rear panel, there are five video inputs and two video outputs and each one includes both composite video and S video configurations.
Connect VCRs, VTRs, LD players, DVD players, and other video components to the video inputs. Connect VCRs, VTRs, and other recording components to the video outputs to make video recordings.
•When connecting a VCR or other video component, make sure you connect its audio and video leads to the same bank (e.g., both to VIDEO 3).
•The VIDEO 5 inputs are located on the front panel.
The flow of the video signals is as follows:
Signals that comes in from VIDEO and S VIDEO INPUT are output to VIDEO and S VIDEO. However, signals that comes in from COMPONENT VIDEO INPUT are only output to COMPONENT VIDEO OUTPUT. When connecting a video player to the COMPONENT VIDEO INPUT jacks, be sure to connect your television to the COMPONENT VIDEO OUTPUT jacks.
4. Connecting a DVD player (DVD)
Using an RCA video cable, connect the video output jack (composite) of the DVD or LD player to the DVD VIDEO IN jack of the
With the initial settings of the
If you connect the DVD or LD player to the COMPONENT VIDEO INPUT 2 jacks, this must be changed at Setup Menu → Input Setup
→Video Setup → Component Video (see page 53).
Using an RCA audio connection cable, connect the audio output jacks of the DVD or LD player to the DVD AUDIO IN jacks of the
If the device has a digital output, connect it to either the DIGITAL INPUT COAX jack or DIGITAL INPUT OPT jack of the TX- NR900/900E depending on the type of connector on the DVD player.
With the initial settings of the
If the digital connection is made at a different jack, this must be changed at Setup Menu → Input Setup → Digital Setup (see page 51).
18