Onkyo TX-NR900E Connecting the power, Turning on the power from the remote controller

Connecting the power

(USA and Canadian models) (All models other than USA and Canadian models)

STANDBY/ON

STANDBY indicator

MASTER VOLUME

STANDBY/ON

STANDBY

ZONE 2 (GRN )

AUDIO

REC ( RED ) DVD

VIDEO 1

VIDEO 2

VIDEO 3

VIDEO 4

VIDEO 5

TAPE

TUNER

PHONO

C D

NET AUDIO

PURE AUDIO UPSAMPLING

SELECTOR

DISPLAY

VCR 1

VCR 2

PUSH TO OPEN

TX-NR900

To wall outlet

STANDBY/ON		ON
STANDBY indicator		STANDBY
		RCVR
		MASTER VOLUME
STANDBY/ON
STANDBY
POWER
ON OFF
ZONE 2 (GRN )
AUDIO REC ( RED ) DVD VIDEO 1	VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5TAPE TUNER PHONO C D NET AUDIO	DISPLAY
PURE AUDIO UPSAMPLING SELECTOR
VCR 1	VCR 2
		PUSH TO OPEN
		TX-NR900E
POWER	To wall outlet

•Before you plug in the TX-NR900/900E, confirm that all connections have been made properly.

•Turning on the power may cause a momentary power surge, which might interfere with other electrical equipment on the same circuit, such as computers. If this happens, use a wall outlet on a different circuit.

(All models other than USA and Canadian models)

•The TX-NR900/900E is shipped with the main power (POWER) switch in the on position ( ON ). When the power cord is plugged in for the first time, the TX-NR900/900E will automatically enter the standby state and the STANDBY indicator will light (same condition after step 2 below).

Turning on the power from the remote controller

Before you can use the remote controller, you must perform steps 1 and 2 above and place the TX-NR900/900E in the standby state.

1. Press the RCVR MODE button.

The RCVR MODE button lights.

2. Press the ON button to turn on the TX-NR900/900E (take it out of the standby state).

To return the TX-NR900/900E to the standby state, press the STANDBY button.

Turning on the power

Memory preservation (Other than USA and Canadian models)

1. Plug the power cord into an AC wall outlet.

(USA and Canadian models)

The STANDBY indicator will light up.

(All models other than USA and Canadian models)

Press the POWER switch to set the

TX-NR900/900E to standby state.

POWER

The STANDBY indicator will light up.

ON OFF

STANDBY

STANDBY

The TX-NR900/900E does not require memory preservation batteries. A built-in memory backup system preserves the contents of memory (e.g., speaker settings and surround settings) during power failures and even when the power is turned off with the POWER switch. The backup system is charged when the POWER switch is turned on.

The length of time that the memory will be preserved will vary depending on the ambient climate. On the average, memory contents are protected over a period of a few weeks after the last time the unit has been turned off. This period may be shorter

2.Press the STANDBY/ON button to turn on the TX- NR900/900E.

The display will light up and the	STANDBY/ON
STANDBY indicator will turn off.			STANDBY
If you press the STANDBY/ON button
again, the receiver returns to Standby		Turn off
state.

when the unit is exposed to a highly humid climate.

Memory preservation (USA and Canadian models)

The TX-NR900 does not require memory preservation batteries.

Abuilt-in memory backup system preserves the contents of memory (e.g., speaker settings and surround settings) during power failures and even when the unit is unplugged. The unit must be plugged in order to change the back-up system.

The length of time that the memory will be preserved will vary depending on the ambient climate. On the average, memory contents are protected over a period of a few weeks after the last time the unit has been unplugged. This period may be shorter when the unit is exposed to a highly humid climate.

30