System Configuration
Speaker Setup
Although using EzSet/EQ to enter the settings for speaker “size” and crossover point, you may wish to make changes to those settings, or to manually enter a complete speaker profile for your system. In addition, for systems where you with to have separate speaker configuration set- tings for each input, rather than use the same settings for all inputs, you may also configure that option in these menus. Two separate menus are used to enter this information, and you may change the data on either or both, as needed.
The SPEAKER SIZE menu tells the AVR about the bass reproduction capabilities of your speakers. This, in turn, determines which speakers receive bass information that is derived from audio tracks or specifically intended for reproduc- tion by
The SPEAKER
To configure the speakers in your system for use with the AVR 635, or to check the settings entered by EzSet/EQ, check the settings on the various
* S P E A K E R S I Z E *
→L E F T / R I G H T : S M A L L
C E N T E R | : | S M A L L |
| |
S U R R O U N D : | S M A L L |
| ||
S U R R B A C K : | N O N E M A I N | |||
S U B M O D E : | S U B |
|
S U B S I Z E : 1 0 i n / 2 5 0 m m
E Z S E T S E T T I N G S : O F F O N
B A C K T O M A N U A L S E T U P
Figure 9
On the SPEAKER SIZE menu (Figure 9), you will see either the factory default settings or, if EzSet/EQ has been run, the settings recorded by the test results. In the case for the main speaker channels, each speaker position (front left/right, center, surround left/right and surround back left/right) you have the option of telling the system if the speakers used are “small” or “large”. These descriptions do not describe the actual physical size of the speakers, but rather refer to the type of speaker. For each of these settings, select LARGE when the speakers in a particular position are traditional
If you are in doubt as to which setting best describes your speakers consult the specifications in the speakers’ owner’s manual, visit the speak- er manufacturer’s web site or ask the dealer or installer from whom you purchased the speakers.
Begin your changes to the speaker setup process by making certain that the cursor is pointing at the LEFT/RIGHT line, which sets the con- figuration for the front left and right speakers. If you wish to make a change to the front speakers’ configuration, press the ‹/ › Navigation Button Eso that either LARGE or SMALL appears, matching the appropriate description from the definitions shown above.
IMPORTANT NOTE: If a change is made to this, or any speaker position, when you press the ‹/ › Navigation Button E, an
When SMALL is selected,
When LARGE is selected, a
Important Note: When a speaker set with a sub- woofer and two front satellites connected to the Sub´s speaker outputs is used, the Sub´s inputs must be connected to the Front speaker out- puts and LARGE must be selected for the front speakers (and NONE for the subwoofer, see below).
3.When you have completed your selection for the front channel, press the ¤ Button Eon the remote to move the cursor to CENTER.
4.Press the ‹/› Buttons Eon the remote to select the option that best describes your center speaker, based on the speaker definitions shown below.
When SMALL is selected,
When LARGE is selected, a
NOTE: If you choose Logic 7 as the surround mode for the particular input source for which you are configuring your speakers, the AVR will not make the LARGE option available for the center speaker. This is due to the requirements of Logic 7 processing, and does not indicate a prob- lem with your receiver.
When NONE is selected, no signals will be sent to the
5.When you have completed your selection for the center channel, press the ¤ Button Eon the remote to move the cursor to
SURROUND.
6.Press the ‹/› Buttons Eon the remote to select the option that best describes the surround speakers in your system based on the speaker definitions shown on page 27.
When SMALL is selected, with all digital sur- round modes
When LARGE is selected, a
SYSTEM CONFIGURATION 27