Operation
Digital sound tracks available on laser discs. Connect the RF output of the LD player to the demodulator and then connect the digital output of the demodulator to the Optical or Coaxial inputs *Ó of the AVR. No demodulator is required for use with DVD players or DTS- encoded laser discs.
In order to provide maximum playback compati- bility with DVDs, the AVR 635 receiver will always default first to the playback mode embedded in a disc’s digital “flag” information. For Dolby Digital discs, the following playback modes are initially selected after the AVR locks to the incoming digi- tal audio data stream to identify the selected:
•When a 5.1 audio stream is detected, the Dolby Digital 5.1 format will be selected, regardless of the number of speakers in your system, in compliance with Dolby Laboratories licensing requirements.
•When a disc with the Dolby Digital EX format flag is played, your system will automatically switch to the EX mode when seven main chan- nel speakers are available.
•When a disc with Dolby Digital data, but only 2.0 audio is detected, the default mode is Dolby Digital with Pro Logic II
•Depending on the number of speaker channels available in your system, once the AVR locks to the digital signal, you may select any surround mode or
DTS
DTS is another digital audio system that is capa- ble of delivering 5.1, 6.1 or 7.1 audio. Although both DTS and Dolby Digital are digital, they use different methods of encoding the signals, and thus they require different decoding circuits to convert the digital signals back to analog.
rear panel | or front panel *Ó. |
In order to listen to DVDs encoded with DTS sound tracks, the DVD player must be compatible with the DTS signal as indicated by a DTS logo on the player’s front panel. Note that early DVD players may not be able to play DTS- encoded DVDs. This does not indicate a problem with the AVR, as some players cannot pass the DTS signal through to the digital outputs. If you are in doubt as to the capability of your DVD player to handle DTS DVDs, consult the player’s owner’s manual.
Please note that some DVD players are shipped with their output set for Dolby Digital only. To insure that DTS data is being sent to the AVR, please check the setup menu system on your DVD player to make certain that DTS data output is enabled.
PCM Audio Playback
PCM (Pulse Code Modulation) is the non- com- pressed digital audio system used for compact discs,
Connections may be made to either the Optical
or Coaxial inputs on the rear panel or the front panel Digital Inputs *Ó.
To listen to a PCM digital source, first select the input for the desired source (e.g., CD) to feed its video signal (if any) to the TV monitor and to pro- vide its analog audio signal for recording. Next press the Digital Select button ÛGand then use the ⁄/ ¤ buttons Eon the remote, or the Selector buttons 7$ on the front panel, until the desired choice appears in the Lower Display Line ˜, then press the Set button @Fto confirm the choice.
In most cases this will be 48 KHZ, though in the case of specially mastered,
The PCM 48 KHZ indication will also appear when modes or inputs are changed for analog sources. In those cases the system is telling you the sampling frequency used internally at the output of the
During PCM playback the unit automatically will turn to the default surround mode or to the LOGIC 7 mode but you also may select any surround mode except Dolby Digital or DTS. When an HDCD encoded disc is being played (see below) and the CD player is connected to the AVR via a digital connection, select Surround Off
as the Surround mode to enjoy the benefits of the HDCD process.
HDCD
HDCD, which stands for High Definition Com- patible Digital®, is a sophisticated process that enables the AVR to deliver outstanding
When a CD with the HDCD recording is played, the AVR is able to take advantage of the special recording process that is used in the creation of HDCD disc. The special circuitry enables audio with extraordinary fidelity, stunning resolution and the highest possible overall quality.
As long as a digital input and the pure Stereo mode (Surround Off) are selected, the AVR will automatically sense that it is an HDCD recording.
It is important to note that the HDCD process is completely compatible with standard recordings. Indeed, the
MP3 Audio Playback
The AVR is one of the few A/V receivers to pro- vide
benefits of listening to MP3 audio through the AVR’s high current amplifier and the speakers from your surround system, rather than the small- er speakers and low powered amplifiers typically used with computers.
To take advantage of the AVR’s MP3 capabilities, simply connect the digital (SPDIF) output of a computer sound card able to feed the MP3 for- mat to its digital output, or the digital (SPDIF) output of MP3 compatible CD or DVD players or of a portable MP3 player with a digital output to
either the rear panel Digital Inputs or the front panel Digital Inputs *Ó.
NOTES:
•The AVR is only capable of playing signals in the MP3 (MPEG 1/Layer 3) format. It is not com- patible with other computer audio codecs.
, HDCD®, High Definition Compatible Digital® and Pacific Microsonics™ are either registered trademarks or trademarks of Pacific Microsonics, Inc., in the United States and/or other countries. HDCD System manufactured under license from Pacific Microsonics, Inc.
OPERATION 37