When two or more P2 card slots contain cards, this function allows the target P2 card to be switched in order. Even when the free space of a P2 card is used up, this function continues recording while erasing existing data.
To use this function, the menu option LOOP REC MODE must be set to “ON” The option LOOP REC MODE can be found in the <REC FUNCTION< screen on the SYSTEM SETTINGS page.
|
| Card1 |
| Card2 |
|
| Card3 | |
Before loop |
|
|
|
|
|
|
|
|
| No content |
| Content |
|
|
|
| |
recording starts |
|
|
|
|
|
| ||
|
| recorded |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
Recording starts |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
Recording Cycle 1 |
| A |
|
| B |
|
| C |
|
|
|
|
|
|
|
|
|
Recording Cycle 2 |
| D |
|
| B |
|
| C |
|
|
|
|
|
|
|
|
|
The data is recorded in the free space of each P2 card (in order of A
B C). When the free space is used up, the content on A is erased to perform a new recording on D.
<Note>
z When the loop recording capability is used, each P2 card must have at least one minute of free space.
z During loop recording, the P2 CARD ACCESS LEDs for all target P2 cards illuminate in orange. Note that if any of the target P2 card is removed, loop recording stops.
z When the menu option LOOP REC MODE is set to ON, the viewfinder and display window both show “LOOP”.
However, when only one card is inserted, or when each card has less than one minute of free space, the loop recording capability does not work, even if the option LOOP REC MODE is set to ON. If this is the case, the indication “LOOP” flashes in the viewfinder and on the display window.
Terminating the Loop Recording ModeYou can terminate the loop recording mode by either: z Turning off the POWER switch of the
When recording is paused, pressing the RET button automatically locates the last two seconds of video just recorded, and the viewfinder provides video playback.
After playback, the video
The picture location/playback duration can be increased to up to
10 seconds by continuously pressing the RET button. For short
clips, however, when the start of a clip is located, continuously 3 pressing the RET button does not play back any clips before that
clip.
The function of the RET button may be assigned to a desired user button by using one of the menu options USER MAIN SW, USER1 SW or USER2 SW. These options can be found in the <USER SW> screen on the CAM OPERATION page.
When recording is paused, pressing the PLAY/PAUSE button plays back the last recorded clip, from the beginning. After completion of playback, the
<Note>
When the OUTPUT SEL switch on the side panel is positioned at [MEM], the video for REC REVIEW is output from the video output connectors (VIDEO OUT and MON OUT connectors), and also to the viewfinder.
Note that when a backup device is connected to back up the video the pictures for REC REVIEW are backed up.
Recording starts |
| Recording pauses | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| Recorded clip |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| The PLAY button plays back | The RET button puts | ||||||
| the clip from the beginning. | the video camera- | ||||||
|
|
| recorder into REC | |||||
|
|
| REVIEW mode. | |||||
27