Network
RQT9334
(ENG)
29
In most cases, default settings can normally be use d
without making any changes.
Set the IP address only when the router has no DHCP
serve r func tions or whe n the r outer’s DHCP server
function is disabled.
After per forming steps 1 – 3 (>28)
4Press [3,4] to select “IP Address Auto
Configuration (DHCP)” and press [2,1] to
select “Off”.
≥Gen erall y le av e “O n” se le cted .
≥When “Off” is selected, “DNS Auto Configuration
(DHCP)” (>below) is also automatically “Off”.
5Press [3,4] to select “IP Address”,
“Subnet Mask” or “Default Gateway” and
press [OK].
6En ter numb ers wi th the numbere d buttons
and press [OK].
≥If a wrong number is entere d, th en pr ess [CANC EL].
7
Press [
2
,
1
] t o se l ect “ Yes” and pres s [ OK].
≥
After checking the specification s for your broad band router,
enter each number. If the number is unknown, then check the
num ber of other devices such as personal com puters connected
via a LAN cable. Assign a differen t number from those of other
devices for the “IP Address” a nd th e sam e number for others.
≥The numeric input range is between 0 and 255.
In most cases, default settings can normally be use d
without making any changes.
When setting an assigne d DNS server from your Internet
serv ic e prov ide r, perform the fol lowin g set tings.
After per forming steps 1 – 3 (>28)
4Press [3,4] to select “DNS Auto
Configuration (DHCP)” and press [2,1] to
select “Off”.
5Press [3,4] to select “Primary DNS” or
“Seco nd ary DNS”a nd press [OK].
6En ter numb ers wi th the numbere d buttons
and press [OK].
≥If a wrong number is entere d, th en pr ess [CANC EL].
7
Press [
2
,
1
] t o se l ect “ Yes” and pres s [ OK].
≥Fol lo w th e in str uc tio ns g iv en by yo ur I nter n et ser v ic e pro vi de r
and e nt er t he num be rs. I f th e nu mb er is u nk now n, th en che ck
the number of other devices such as personal computers
connected via a LAN cable and assign the same number.
≥The numeric input range is between 0 and 255.
When the connection test results in “Fail” after the IP and DNS-
IP addresses are assigned, perform the following settings.
After perfor ming steps 1 – 3 (>28)
4Press [3,4] to select “Auto Detect
Conn ection Speed” and press [2,1] to
select “Off”.
5Press [3,4] to select “Connection Speed
Set t i ng ” an d pre ss [2,1] to select a
connection speed.
≥Selec t a connec tio n speed in accordance with the
environment of the network connected.
≥When the set ting s are changed, the network conn ecti on may
be slower o r dis abled depending on th e device.
Always test the connection when new “Proxy Server Settings”
have been made.
1Press [ SETUP].
2Press [3,4] to select “Network” and
press [OK].
3Press [3,4] to select “Proxy Server
Settings” and press [OK].
4Press [3,4] to select “Connection Test”
and press [OK].
“Testing” : The test is in progres s.
“ Pas s”: The conne ction is completed.
Pres s [ R ETU RN ] to ex it.
“Fail”: Please check the connection and settings.
In most cases, default settings can normally be used
with out maki ng any changes.
Pl ea se use th is se t tin g wh en in st ru cte d to b y yo ur I nte rne t
ser vic e p ro v ide r.
After perfor ming steps 1 – 3 (Dabove)
4Press [3,4] to select “Proxy Address”
and press [OK].
(Continued on the next page)
Setting the IP address
Setting the DNS-IP
192 ...
1
Primary DNS
Please input Primary DNS and press
[OK]. Press [CANCEL] to delete the selected
character. To clear this setting, delete all
characters and press [OK].
Number
0
-
9
Setting the connection speed
Testing of “Proxy Server Settings”
Setting the proxy server
RETURN
Proxy Server Settings
Reset to factory preset
Proxy Address
Proxy Port Number
OK
0
Connection Test
DMPB15P-RQT9334_eng.book 29 ページ ２００９年３月２８日 土曜日 午後２時３９分