Panasonic DMR-E65 Timer recording, Press F Timer, Using G-CODEsystem to make timer recordings

Timer recording

4 Press [ENTER].

DVD

		TV
	INPUT SELECT		CH	VOLUME
		AV
	DVD DRIVE SELECT SD/PC
Numbered	1	2	3
	4	5	6	CH
buttons
				G-Code
	7	8	9
	CANCEL			MANUAL SKIP
¢ CANCEL		0	-/--
	SKIP		SLOW/SEARCH

	STOP	PAUSE PLAY/x1.3
DIRECT	DIRECT NAVIGATOR			FUNCTIONS
NAVIGATOR	TOP MENU
3,4,2,1
		ENTER
ENTER
	SUB MENU			RETURN
	PROG/CHECK	DISPLAY	STATUS	TIME SLIP
PROG/CHECK
FTIMER	TIMER	ERASE	REC MODE	REC
	F
			CREATE	AUDIO
			CHAPTER
	A	B	C

G-Code

PLAY

REC MODE

The settings are stored.

	TIMER					Remain
								1:58 SP
	RECORDING
						12:55:00 15. 7.			TUE
		No.	Name	Date Start	Stop	Mode	spaceDisc			Check to make sure
		01	ARD	15/ 7 TUE 19:00	20:00	SP	OK			“OK” is displayed
				New Timer Programme
										(➡page 19).
Repeat steps 1–4 to programme other recordings.
5 Press [F TIMER].
The unit turns off and “F” lights on the unit’s display to
indicate timer recording standby has been activated.
[RAM]
Even if the unit is in timer recording standby, play starts when you
press [1] (PLAY) or [DIRECT NAVIGATOR]. Timer recording works
even during play.											Recording
∫ To release the unit from recording standby
Press [F TIMER].
The unit turns on and “F” goes out.
≥Be sure to press [F TIMER] before the programme start time to
put the unit on recording standby. Timer recording will work only
if “F” is displayed.
∫ To cancel recording when recording has
already begun
Press [F TIMER].
≥You can also press and hold [∫] on the main unit for more than
3 seconds to stop recording.

[RAM] [DVD-R]

You can enter up to 16 programmes up to a month in advance.

Using G-CODE®system to make timer recordings

Entering G-CODEnumbers is an easy way of timer recording. You can find these numbers in TV listings in newspapers and magazines.

1 Press [G-Code].

G-Code	Remain
		1:58 SP
	12:53:00 15. 7. TUE

Enter G-Code Number by using 0-9 keys.

2 Press the numbered buttons to enter the G-CODEnumber.

Press [2] to move back to correct a digit.

3 Press [ENTER].

TIMER			Remain 1:58 SP
RECORDING
			12:54:00 15. 7. TUE
Name	Date	Start	Stop	Mode
1 ARD	15/ 7 TUE	19:00	20:00	SP
				Programme Name

≥Confirm the programme and make corrections if necessary using [3, 4, 2, 1] (➡page 18, step 3).

≥When “-- ---” appears in the “Name” column, you cannot set timer recording. Press [3, 4] to select desired programme position. After you have entered the information of a TV station, it is kept in the unit’s memory.

≥You can also press [REC MODE] to change the recording mode.

≥Programme Name

Press [2, 1] to select “Programme Name” and press [ENTER] (➡page 38).

[Note]

≥“F” flashes for about 5 seconds when the unit cannot go to

timer recording standby (e.g., a recordable disc is not in the

disc tray).

≥If the unit is not put in the timer recording standby mode at the

latest 10 minutes before the programmed timer recording

starting time, the “F” flashes on the unit display. In this case,

press [F TIMER] to put the unit in the timer recording standby

mode.

≥When you programme successive timer recordings to start

immediately one after the other, the unit cannot record the part

at the beginning of the later programmes (a few seconds when

recording with DVD-RAM and approximately 30 seconds when

recording with DVD-R).

RQT7450

17