Manuals / Brands / Computer Equipment / Projector / Panasonic / Computer Equipment / Projector

Panasonic PT-D5600E, PT-D5600EL, PT-DW5000E, PT-DW5000EL, PT-DW5000E Replacing the lamp unit

1 60

Download 60 pages, 3.36 Mb

44

Insert the power cord plug into the wall outlet and then

press the MAIN POWER switch.

Press the “ I ” button so that a picture is projected onto

the screen.

Press the “MENU” button to display the MAIN MENU

screen, and then press the and buttons to move

the cursor to select “OPTION2”.

Press the “ENTER” button to display the “OPTION2”

screen, and select “SYSTEM INFORMATION” with the

and buttons.

Press the “ENTER” button.

The SYSTEM INFORMATION screen will be displayed.

Press and hold the “ENTER” button on the projector or

the remote control for approximately 3 seconds.

An item “LAMP TIME RESET” will be added.

Select the lamp which has been replaced with the and

buttons.

LAMP1: Replace the LAMP UNIT 1

LAMP2: Replace the LAMP UNIT 2

Press the ENTER button, and when the “LAMP TIME

RESET” display flashes, press the ENTER button again.

The used hours of the specified lamp unit will be reset to zero.

When more than one lamp has been replaced, repeat the procedure from

step .

• If the power does not turn on even after turning the MAIN

POWER switch “I”, turn the MAIN POWER “O”, confirm that

the lamp unit and door are installed correctly, and turn on

again.

Attention

MENU

PICTURE

ADVANCED MENU

OPTI0N2

TEST PATTERN

OPTION1

POSITION

LANGUAGE

LAMP TIME RESET

LAMP1

LAMP2

LAD55

LAD55L

LAD55 1433h

0h

1100h

0h

LAD55L

SYSTEM INFORMATION

ROM VERSION

HIGH 200h

TOTAL 300h

LAMP2 LOW

SET RUNTIME 300h

LAMP1 LOW 100h

100h

1. 00. 00

• When the “LAMP TIME RESET” display flashes, the lamp

time reset can be canceled by pressing the MENU button.

• The used hours of the lamp units can also be reset to zero

by taking the following action instead of steps to .

When lamp unit 1 has been replaced:

In the standby mode, press the number buttons in the

sequence of 737381, and then press the ENTER button.

When lamp unit 2 has been replaced:

In the standby mode, press the number buttons in the

sequence of 737382, and then press the ENTER button.

When the used hours have been reset, the lamp monitor

(LAMP1/LAMP2) will flash for 3 seconds.

Note

Replacing the lamp unit

Contents

Main Dear Panasonic Customer: IMPORTANT SAFETY NOTICE Page Contents Precautions with regard to safety WARNING Precautions with regard to safety Caution Accessories Precautions on handling Precautions on transport Precautions on installation Disposal Precautions on use Name and function of parts < When the operation mode selector is set to Projector > Remote control Name and function of parts <When the operation mode selector is set to Computer> Front and side of the projector Status LED lights Name and function of parts Rear view of the main unit Controls on rear panel Side-mounted connection terminals Using the remote control unit Loading dry cells 1.Open battery compartment lid. 2.Insert the dry cells. 3.Close the battery compartment lid. Using the remote control as a PC mouse Operation mode selector switch Setting projector ID number to remote control Using a wired remote control Using the remote control unit Installation Projection schemes Installation geometry Projection distance by projection lens The height position (H) of the ET-DLE050 is SH/2. Screen aspect ratio 4:3 Screen aspect ratio Installation The height position (H) of the ET-DLE050 is SH/2. Note Black bands will appear at the top and bottom of the screen. Screen aspect ratio PT-DW5000E, PT-DW5000EL Calculation formulas for projection distance by lens types Connection Setup precautions Example of connecting with PCs Example of connecting with AV products Projection Powering up the projector Making adjustment and selection Powering off the projector Direct power off function How to adjust the lens How to install and remove the projection lens (optional) How to install the projection lens How to remove the projection lens How to adjust the lens focus, lens zoom and lens up/down position movement (optical shift) Using the digital zoom ( D.ZOOM +) function Press the D.ZOOM + button of the remote control. Change the magnification with the D.ZOOM + button. Use buttons to move the magnified image. To restore the original image, press the MENU button. B C D E On-screen menus Structure of menu screens POSITION (page 30) OPTION1 (page 34) LANGUAGE (page 33) Basic menu operations Press the MENU button. Select (highlight) the desired item with the or buttons. Press the ENTER button to enter your selection. BRIGHT 32 Adjusting the picture PICTURE MODE BRIGHT CONTRAST COLOR Adjusting the position POSITION ASPECT AI TV-SYSTEM KEYSTONE ZOOM CLOCK PHASE How to use ADVANCED MENU INPUT RESOLUTION CLAMP POS. DIGITAL CINEMA REALITY BLANKING Changing the display language RASTER POSITION XGA MODE SXGA MODE OPTION1 settings COLOR CORRECTION CONTRAST MODE AUTO SIGNAL BACK COLOR OPTION2 settings ID FRONT/REAR DESK/CEILING LAMP SELECT RS232C SYSTEM INFORMATION FAN CONTROL1 FAN CONTROL2 FUNC1 Displaying the internal test pattern Cycle of displayed internal test patterns Black on white ground White on black ground Setting the security Setting the password Setting the network Connecting the PC System requirements Operation is not guaranteed for all computers that meet the above conditions. Connection example Using the serial terminals Pin assignments and control Using the REMOTE 2 terminal Cable specifications Control commands Indication of lamp monitor Temperature monitor Lamp monitor Cleaning and replacement of air filter Procedure of cleaning Turn off the main power and remove the power plug from the receptacle. Dismantle the air filter. Set the air filter. Replacing the lamp unit Precautions on lamp unit replacement Timing of lamp unit replacement Indication after 1 300 hours 2(with LAMP POWER set at HIGH) WARNING! Lamp unit replacement steps Caution Replacing the lamp unit Using Web Browser Control Accessing from the Web browser Password change page Basic control page Monitor information page Detail control page Error information page E-mail setup page DNS server set up page E-mail setup page (continuing) POP server setup page Ping test page Contents of mail sent Mail with the contents shown below is sent when the E-mail settings have been established. Click [Network set up], then [Adjust clock] to display the Adjust clock page. Adjust clock page Mail with the contents shown below is sent when an error has occurred. Network config page Network status page Using the PJLinkprotocol Supported commands PJLinksecurity authentication Before asking for service Specifications PT-D5600E PT-D5600EL PT-DW5000E PT-DW5000EL PT-D5600E PT-D5600EL PT-DW5000E PT-DW5000EL Compatible Signal List Note Dimensions Installation dimensions diagram Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) For business users in the European Union Information on Disposal in other Countries outside the European Union Matsushita Electric Industrial Co., Ltd