Panasonic RPWF6000 operating instructions Precautions, Control reference guide

Precautions

Control reference guide

AC adaptor

Handle the AC adaptor carefully. Improper handling is dangerous.

●Do not touch it with wet hands.

●Do not place heavy objects on top of it. Be sure to use the supplied AC adaptor.

Batteries

●The rechargeable battery can be recharged about 300 times. If it’s operating time becomes extremely short, you should replace it.

●Do not mix old and new batteries or different types of batteries.

●Do not heat the batteries or expose them to flames.

●Do not recharge ordinary dry cell batteries.

●Remove the battery if the unit is not to be used for a long time.

●Carry and store the rechargeable batteries in the battery carrying case to prevent contact with metal objects.

●Do not peel off the covering on batteries and do not use if the covering has been peeled off.

Mishandling of batteries can cause electrolyte leakage which can damage items the fluid contacts and may

cause a fire.

The unit

This unit uses the 2.4 GHz radio frequency band. However other wireless equipment may use the same frequency. Be sure to take note of the following to prevent radio wave interference from other equipment.

n Restriction of use

For use only in your country.

n Range of use

The range of use is up to approximately 30 m (98.4 ft.). The range may be less depending on the structure of the building, the environment and any obstacles between the headphones and the transmitter. Such obstacles as reinforced concrete walls and metal doors, in particular, obstruct the transmitter’s

signals.

n Interference from other equipment

Due to radio interference, malfunctions such as sound distortion may occur if the unit is placed too close to other equipment. We recommend keeping the unit as far away as possible from the following devices.

Bluetooth devices, wireless LAN, microwaves, office automation devices, digital cordless telephones and other electronic devices

The unit is designed to automatically avoid radio interference from these household devices. However

the sound will be broken when		radio	interference
occurs. In this case reset the		most	appropriate
frequency (	page 14 [Setting the most appropriate

frequency]).

n Using the unit

●Do not drop, hit or otherwise subject the transmitter or headphones to strong shocks of any kind. This may damage them.

●Do not expose the unit to water or other liquids as it may damage it.

Transmitter’s rear panel	g ATT control (		page 10)
	Switch to [0 dB] when sound from an analog input is
	low. The standard setting is [-8 dB].
	h LINE IN terminal (		page 10)
				ENGLISH
	To connect to the audio out terminals of AV equipment
	such as a video cassette recorder or television (not
	included).
	i DIGITAL IN 1, 2 terminal (optical digital input)
	(	page 9)
	To connect to digital equipment such as a DVD player
	or a television (not included).

jDIGITAL OUT terminal (optical digital output)

( page 9)

The same digital signal as the input signal selected with the INPUT SELECT control is output.

● When ANALOG is selected, the same digital signal as the input signal to DIGITAL IN 2 is output.

INPUT
SELECT	DIGITAL OUT
control
DIGITAL 1	The same signal as the signal input
	to DIGITAL 1
DIGITAL 2	The same signal as the signal input
ANALOG	to DIGITAL 2

	k DC IN 9V terminal (	page 6)
	To connect to the supplied AC adaptor.
	(Use only the supplied AC adaptor. Use of other AC
	adaptors with, for example, a different plug polarity is
	dangerous and can damage the unit.)
Headphones	l Ear pad (left)
	m Charging terminal

Control reference guide

n Left housing
o BATT (battery) knob (	page 6)

Transmitter’s front panel

Charging terminal

RQT8948

4

4

aDECODE MODE lamp ( pages 12 to 13)

(DOLBY DIGITAL, DOLBY PRO LOGIC II, DTS, MPEG-2 AAC)

The transmitter automatically distinguishes the recording method of the input signal and the DECODE MODE lamp lights.

bSURROUND lamp ( page 14)

(MUSIC, CINEMA, VOICE)
c SURROUND button (	page 14)

Switch between MUSIC, CINEMA, VOICE and OFF in SURROUND MODE.

d INPUT SELECT ( page 12)

Switch between DIGITAL 1, DIGITAL 2 and ANALOG input.

e ID/TUNING button, lamp ( page 14)

Use when the radio waves are weak.

fOPR/CHARGE (operation/charge) lamp

( page 7)

●It glows red when the headphones are being charged.

●It glows green when the transmitter is in operation.

●It goes out when the charging finishes or when there are no audio signals input for approximately 5 minutes.

p Battery compartment lid
Press BATT to open the battery compartment lid.
Use the supplied rechargeable battery or “LR6, AA”
alkaline dry cell batteries (not included).
q Free-adjusting band (	page 8)
The power turns on automatically and the OPR lamp
lights when you put on the free-adjusting band.

r OPR (operation) lamp

Pull up the free-adjusting band and check that the OPR lamp glows red. You can now use the headphones.

sRight housing

tEar pad (right)

uID button, VOL control

VOL: When adjusting the volume ( page 12)

RQT8948

500

5