Listening to audio from equipment connected to the transmitter
Before using the transmitter, read [Connections] ( page 9 to 10) and ensure that it is connected correctly.
1 | Turn on the equipment connected to the DVD player and so on |
| transmitter. |
2 Select the signal with [INPUT SELECT].
DIGITAL 1: To hear sound from equipment connected to the transmitter’s DIGITAL IN 1 terminal.
DIGITAL 2: To hear sound from equipment connected to the transmitter’s DIGITAL IN 2 terminal.
ANALOG: To hear sound from equipment connected to the transmitter’s LINE IN terminal.
Note
With dual sound sources (MAIN/SUB), select the desired sound on the player or television connected through the LINE IN terminal.
3 Take the headphones off the transmitter.
4 Put the headphones on your head.
Make sure that the headphones are positioned so that the right | |
housing (R) goes over the right ear and the left housing (L) over | |
the left ear. Then put the headphones straight down onto your | |
head. Doing this will ensure that the auto power on/off function | |
( | page 8) works correctly. |
● The OPR lamp j on the right housing k glows red and the | |
| power automatically turns on. |
5 Start play on the equipment selected in step 2.
● The OPR/CHARGE lamp h on the transmitter will light green and radio waves will be emitted. The most appropriate frequency is automatically set.
● The DECODE MODE lamp l glows approximately 5 seconds later depending on the signal sent from the connected equipment.
6 Use [VOL] to adjust the volume.
● The volume is the same as when the headphones were previously used.
● The volume will keep changing while the [VOL] control is pushed to either side.
| m To increase the volume | |
RQT8948 | n To decrease the volume | |
Refer to page 14 for information about the SURROUND effects. | ||
|
12
Note
● When watching movies, be careful not to turn up the volume too high during quiet scenes. The movie may |
| |
suddenly switch to a very noisy scene and you could damage your ears if the volume is raised too high. | ENGLISH | |
● Avoid listening for prolonged periods of time to prevent hearing damage. | ||
● Be sure to use the headphones within the range of the radio waves. | ||
| ||
● Discontinue use if you experience discomfort. Continued use may cause rashes or other allergic reactions. |
|
For your reference
●If you disconnect the AC adaptor from the transmitter before taking off the headphones, there may be static noises.
●The actual location of the sound may be difficult to recognize with music and audio only sources such as music CDs.
●This unit simulates the average person’s HRTF※. However individual differences in human’s HRTF mean that the effect of this system will vary between individuals.
※ An abbreviation for Head Related Transfer Function.
Time required for mode changes
The actual time required for the unit to change to a particular mode after it has been selected using the slide switch on the transmitter, may vary between individual modes. This is due to different internal systems being used to change to different modes.
DECODE MODE lamp l
The transmitter automatically distinguishes the recording method of the input signal and this lamp lights as shown below. When switching to DOLBY DIGITAL/DTS and so on, do so on the connected equipment e.g. the DVD player.
●DOLBY DIGITAL: Signals recorded in DOLBY DIGITAL format.
●DOLBY PRO LOGIC II: Analog input signals, digital input signals (PCM
DIGITAL
●DTS: Signals recorded in DTS format.
●
For your reference
When any function other than [PLAY] - such as
When you are unable to hear any sound from the headphones (MUTING function)
If the headphones are used outside the range of the radio waves or the radio waves weaken, reception will | |
decline and the MUTING function will come on. No sound will then be heard from the headphones. If this | |
happens, move nearer to the transmitter and the MUTING function will automatically switch off. If the sound | |
is still broken, reset the headphones to the most appropriate frequency.( | page 14 [Setting the most |
appropriate frequency]) |
|
If no audio signal is received at the transmitter for more than approximately 5 minutes
The radio waves being emitted from the transmitter automatically stop and the transmitter’s OPR/CHARGE |
|
lamp goes out. The radio waves start being emitted again when an audio signal is received. When the input |
|
audio (analog only) continues to be very low for more than 5 minutes (approximately), the radio waves being | RQT8948 |
emitted from the transmitter may stop. If this happens, increase the volume level on the connected equipment | |
If a noise signal is input from equipment connected by the LINE IN terminal, the output of radio waves may not | |
and decrease the volume level on the headphones. |
|
stop. | 13 |
|
12 | 13 |