Panasonic 35, UJ30 6.3Default settings mode

Operation modes

6.3Default settings mode

This mode is used for the units (°C/°F) for head tem perature readings, for switching between READY/BUSY signal, and for setting the buzzer ON/OFF.

* The default values are Celsius (°C) for temperature display, BUSY, and buzzer ON.

[Default settings mode]

1.While pressing down the MODE switch power ON the controller.

2.When the display starts up 1 C/F is displayed. [Switching between °C/°F display]

1.Use △/▽ to switch between °C (Celsius)/°F (Fahrenheit).

2. Press the SET switch. 2 A/b will be displayed. [Switching between READY/BUSY signal]

1.Use △/▽ to switch between A=READY/b=BUSY.

2.Press the SET switch. 3 On/oFF will be displayed. [Switching the buzzer ON/OFF]

1.Use △/▽ to switch between buzzer ON/OFF.

2.Press the SET switch. 1 C/F will be displayed. [Exiting from default settings mode]

1.Hold down the SET switch to switch to operation mode.

[Restoring default settings

(all settings are restored to their initial default values)]

1.While in default settings mode, press the MODE switch.

2.EE will be displayed.

3.Hold down △/▽.

4.		will be displayed.

5. Hold down SET.			EE		will be displayed. When

EECLr appears all settings have been restored to their original default values, and the controller returns to operation mode.

19

Contents

LED UV Curing System Aicure SPOT Type Safety Precautions for Users Laser products Preventive safety measures for users (summary) Safety features ■Remote interlock ■Control by a key switch ■LED radiation emission warning ■Emergency reset Labels ■Warning labels in Japanese (JIS) ■Description ■Warning labels in Chinese (GB standards) ■Warning labels in English (IEC/EN standards) Prohibited Mandatory Instruction Precautions for use ■General precautions ■Installation environment Ambient temperature Ambient humidity: Warranty Period Extent of Warranty Page Contents 1 Features of the ANUJ 3000/3500 ■High-powerirradiation: 10,000 mW/cm2 (with ANUJ6423 lens) initial value) ■UV curing without temperature increases ■UV intensity stabilization Features of the ANUJ 3000/3500 The ■Universal design for easy operation ■Multiple safety features ■Detachable terminal blocks for external connection ■Universal power supply 2 Part names and functions Controller Optional parts (sold separately) Front of the controller UV sensor (option) Rear of the controller AC adapter ●Front 4.1Installation conditions 4.2 General guidelines for irradiation distance and UV intensity Page 5.1Hooking up the connection cable Connection cable Getting started <Procedure 1.Plug in the connection cable 2.Connect the LED head to the connection cable 3.Remove the protective cap from the LED head 5.3Connecting the external control signals 5.4 Connecting the AC adapter 5.5Power-onoperation 6.1Operation mode (default mode when power is turned on) Operation modes Page Page 6.2UV measurement and Auto tuning mode Page 6.3Default settings mode 6.4Timing chart Page Page Page 7.1External input/output control External control Output Specification ・Rated load voltage: 5 V DC to 28 V DC ・Max. load current: 100 mA (per 1 output) ・Maximum voltage drop is less than 0.9 V when output is given 7.2Serial communication control Page Page Page 7.3Communications address map Page Page Page Page Page Page Page Page 7.4Setup tool application for UJ35 Page Page Page Page • LED status for each CH differentiated by color • When irradiation is possible, READY ON is highlig hted • If an error occurs, an error number is displayed • Panel showing error list can be displayed at any time • During irradiation START is highlighted Page 8 Warning indications ■Temperature warning ■Error codes 9.1Safety circuit 10.1Outline of specifications Specifications 11 Dimensions Page Page 12.1Options and spare parts Option and spare parts list 12.2How to replace the lens unit 12.3Fitting the mounting bracket Troubleshooting Manual revision history