(3)Move the cursor to "PTZ SELECT" and press the [SET] button.

PTZ SELECT

Cam1 Cam2 Cam3 Cam4

Cam5 Cam6 Cam7 Cam8

OK

 

Cancel

Move the cursor to the desired channel by using the direction buttons (up/down). Select the channel by using the direction buttons (right/left).

In the above figure, "Cam1" is selected in the "PTZ SELECT" menu. No other camera are selected in other channels.

(4)Press the [MENU] button. "WJ-RT208 SETUP MENU" appears. Refer to step (1).

(5)Move the cursor to "CAMERA SETUP" and press the [SET] button.

The "CAMERA SETUP" menu appears. Select "PTZ Protocol".

When using the Panasonic’s camera, select "PANA- SONIC" using the direction buttons (left/right).

In other cases, refer to the relevant instruction manual for that camera.

CAMERA SETUP

 

Channel No.

1

 

CH Enable

On

 

Mask Area

Set

 

Mask Enable

Off

 

PTZ Protocol

PANASONIC

Rec. Reserve

000

Days

Channel Name

CH1

 

All

OK

Cancel

(6)Press the [MENU] button. "WJ-RT208 SETUP MENU" appears. Refer to step (1).

(7)Move the cursor to "COMMUNICATION SETUP" and press the [SET] button. Then move the cursor to "RS485 SETUP" and press the [SET] button.

RS485 SETUP

Baud Rate

 

19200

 

Data Bit

8

 

Parity

 

None

Stop Bit

1

 

 

 

 

 

 

OK

 

 

Cancel

Note: When the Panasonic's camera is used, make set- tings of the respective parameters according to the above-mentioned procedures. In other cases, refer to the relevant operating instructions.

Caution: In order to maintain normal communication between this unit and the cameras, it is necessary to have completely correct settings for "PTZ SELECT", "PTZ Protocol", and "RS485 SETUP".

The camera control mode comes in three types. Each time the [SET] button is pressed in the state of monitoring, the mode changes. The related icon is displayed in a lower area of the screen.

Pan/tilt control mode

Zoom/focus mode

Iris control mode

Note: For some types of cameras, some controls many not function. Refer to the relevant operat- ing instructions of the camera and confirm whether this unit is enabled to support controls and connections.

2.5.1 Panning/Tilting

(1)Select the desired channel by using the direction button or numeric button. The image frame of the selected channel blinks.

Select the pan/tilt control mode by pressing the [SET]

button once.

The camera pan/tilt control icon is displayed on the screen of the selected channel.

(2)Press the direction button and turn the camera in the proper direction.

Note:

In the pan/tilt control mode, two external units can be connected to the cameras.

When the camera select button [1] is pressed, External Unit 1 is set to ON.

When the camera select button [2] is pressed, External Unit 2 is set to ON.

When the camera select button [6] is pressed, External Unit 1 is set to OFF.

When the camera select button [7] is pressed, External Unit 2 is set to OFF.

(3)Press the [SET] button 3 times to close the pan/tilt con- trol mode.

2.5.2 Auto function (Auto Pan, etc.)

(1)Select the pan/tilt control mode by pressing the [SET]

button once.

The camera pan/tilt control icon is displayed on the screen of the selected channel.

(2)Start the auto function by pressing the [PLAY] button.

Note: Refer to the Operating Instructions of the camera for descriptions of the auto function.

29

Page 29
Image 29
Panasonic WJ-RT208 manual Panning/Tilting, Auto function Auto Pan, etc, Panasonic, CH1, RS485 Setup