Show Command Outputs, Show config | Paradyne Routers specs

Command Line Interface

Show Command Outputs

show console

Displays: console enabled or console disabled

show system

Sample show system display:

May 21 09:53:26 2000

System ID: xxxxxxxx

Model #: xxxx, Serial #: xxxxxxxxxxxx, HW-Rev: xxx

Boot: FW-Version xxxxxxxx

2nd Stage Boot: FW-Version xxxxxxxx

Image 0: FW-Version xxxxxxxx, [active]

Image 1: FW-Version xxxxxxxx

DSP: FW-Version xxx

Selftest Result: [0xxxxx] (if failed) { pass fail }

show config

Sample show config display: syslog { enabled disabled } eth1 frame { DIX 802.3 }

proxy ARP eth1 { enabled disabled } proxy ARP dsl1 { enabled disabled }

NAT disabled or NAT enabled { basic NAT NAPT }

DHCP server { enabled disabled }

DHCP relay { enabled disabled } IP multicast { enabled disabled } IP processing { enabled disabled } 1483 encapsulation { LLC VC Muxing } autologout { enabled disabled }

6371-A2-GB20-10

August 2000

A-13

Image 63

Paradyne Routers manual Show Command Outputs, Show config, NAT disabled or NAT enabled basic NAT Napt

Contents

HOTWIRE DSL Routers Copyright E 2000 Paradyne Corporation All rights reserved Contents Configuring the DSL Router Monitoring the DSL Router Index Document Purpose and Intended Audience About This Guide Section Description Document Summary Document Number Document Title Product-Related Documents Syntax Translation Document Conventions Introduction to Hotwire DSL Routers What is a Hotwire DSL Router?DSL Technologies Supported Network Access Provider NAP Typical DSL Router SystemOptional IP routing with Hotwire DSL Router Features Service Subscriber Accessing the DSL Router Access Control to the DSL RouterLevels of Access Show console Changing Access Session LevelsLocal Console Access Admin enable Setting Up the New Users Login CUSTOMER#. Type configure terminal and press EnterInvalid Characters Value Ascii Hex Translation Local console disabled by conflict Telnet AccessDetermining the Current Access Level Determining the Available Commands Using the List Command Exiting from the SystemChanging the System Identity If you are accessing the DSL router Then Manually Logging OutAutomatically Logging Out Configuring the DSL Router Overview of DSL Router ConfigurationInterfaces for the DSL Router Ethernet and DSL Interface Identifiers Service Domain IP Address Assignments Numbered DSL Interface Unnumbered DSL InterfaceSimplified Network Topology Network Considerations IP Routing Proxy ARP Address Resolution Protocol ARP Network Address Translation NAT Basic NATNetwork Address Port Translation Napt Dynamic Host Configuration Protocol Dhcp Server IP Options ProcessingApplications Supported by NAT Dhcp Relay Agent Security IP FilteringLand Bug/Smurf Attack Prevention Routed vs. Bridged PDUs Routed Network Model Standard mode Configuration Examples DSL Router Configuration Examples Customer Premises CP Basic Configuration Example NAT Mapping Public IP Addresses Private IP Addresses Basic NAT Configuration Example Napt Mapping Public IP Addresses Private IP Addresses Napt Configuration Example Core Router 155.1.3.253 Console Port Connection Dhcp Relay with Proxy ARP Configuration Example Public IP Addresses for Basic NAT Private IP Addresses Dhcp Server with Basic NAT Configuration Example Downstream Router Configuration Example Detecting Problems Monitoring the DSL RouterWhat to Monitor ± Ethernet Link up down Status of InterfacesShow interface Show interface eth1 dsl1 Interface Statistics Show statisticsShow statistics eth1 dsl1 ip Discard Reasons for the Ethernet Interface eth1 1 Clearing StatisticsList of Discard Reasons Clear statistics eth1 dsl1 ip Discard Reasons for the DSL Interface dsl1 1 Discard Reasons for the Ethernet Interface eth1 2 Discard Reasons for IP Discard Reasons for the DSL Interface dsl1 2 Show alarms Diagnostics and TroubleshootingDiagnostics and Troubleshooting Overview Alarms Inquiry Syslog ip ip-addr Syslog enable disableSystem Log Show syslog Syslog Messages 1 Level Description Event Syslog EventsSyslog level level Show log number Syslog Message Display Syslog Messages 2 Level Description EventReporting Ping reply x.x.x.x Request Timed OUT PingPing Test Results Ping reply x.x.x.x bytes of data=nn TraceRoute TraceRoute Test ResultsX.x Command Line Interface Feature Command Line Interface Command Recall NavigationDocument Conventions Ethernet Frame Format Command Line Interface CommandsConfiguration Control Commands RFC 1483 Encapsulation Interface and Service Domain IP Address IP Routing Table Delete eth1ifn dsl1ifnIp route create dest-ipdest-mask next-hop-ip remote Ip route purge Proxy ARP ARP Table Nat basic address ip-addrip-mask Nat basic enableNat napt enable Nat timeout time Nat napt delete udp tcp port Nat basic delete private-ip Nat purge Nat disableDhcp server enable disable Dhcp Server Dhcp Relay Agent IP Packet Processing IP multicast enable disableIP processing enable disable Trap disable enable name of trap Show Command Outputs Show configNAT disabled or NAT enabled basic NAT Napt Show arp Show arp timeoutNAT timeout xx minutes NAT basic mappings Show ip route ip-address Show NAT napt Show trapsShow dhcp server Sample show dhcp relay display Show alarms Show syslog Show log #Show Dhcp relay Show interface Show statistics Configuration Default Settings Configuration Defaults Command Line Shortcuts Customer ParadyneAbc123 Bytes Table B-2. Command Line Input Shortcuts 1 Command Line Input Shortcuts Table B-2. Command Line Input Shortcuts 2 Show interface dsl1 eth1 Table B-2. Command Line Input Shortcuts 3 Configuration Defaults & Command Line Shortcuts Traps & MIBs Snmp OverviewTraps Overview Variable Binding DSL Router Traps System Group MIBs OverviewStandard MIBs MIB II RFC System Ssssssssssss Boot bb.bb.bb 2nd Boot xx.xx.xx DSP Yy.yy.yy H/W Releasezzz CCA part numberº Interfaces Group RFCInterfaces IfEntry IfOperStatus Specifies the current DSL interface Table C-5. IP Group Objects 1 Description Setting/Contents Extension to Interfaces Table RFCIP Group RFC IP Cidr Route Group RFC Table C-5. IP Group Objects 2 Description Setting/Contents IpCidrRouteEntry 11 ± Transmission Group Ethernet-Like MIB RFC Snmp Group Active1 Paradyne Enterprise MIBsDevice Control MIB NoOp1 Device Diagnostics MIB Traceroute ApplpingTestEntry Configure ApplTracerouteResultsEntryAppTracerouteResultsEntry Health and Status MIB DevStatus1DevStatus Factory1-to-active8 Configuration MIB Secondary Interface Configuration MIBPdnInetIpAddressTableEntry Primary Dhcp MIB DSL Endpoint MIB Syslog MIB Accessing the List Command Output DSL Router Terminal EmulationDSL Router Terminal Emulation Terminal Emulation Programs Numbers Index IN-2 IN-3