Configuration MIB, Factory1-to-active8 | Paradyne Routers specs

Traps & MIBs

Configuration MIB

The supported groups used with the DSL Configuration MIB, pdn_Config.mib, are:

HDevice Configuration Copy Group

HTrap Configuration Group

HParadyne Device Configuration Time Group

HTraps

Table C-10. Device Configuration Copy Group Objects Table

Object	Description		Setting/Contents

devConfigAreaCopy	Use to configure the current configuration to the		H noOp (1) ± always reads as this
(devConfigArea1)	factory defaults settings.		value and represents:
	NOTE: ALL current configuration input is		factory1-to-active(8)
	NOTE: ALL current configuration input is
	purged when the DSL router is
	resets as a result of this command.
	Data purged includes:
	±	Interface IP addresses
	±	IP route table entries
	± ARP cache entries
	±	NAT entries
	± DHCP server entries

devConfigTrapEnable	This object determines which trap types are		Bit positions:
(devConfigTrap1)	sent, represented by a bit map as a sum.		H 1 ± warmStart trap
	Allows multiple trap types to be enabled or		H 1 ± warmStart trap
	Allows multiple trap types to be enabled or
	disabled simultaneously.		H 2 ± authenticationFailure trap
			H 4 ± enterpriseSpecific traps
			H 8 ± LinkUp trap
			H 16 ± LinkDown trap

devConfigTimeOfDay	Displays the current time.		Ð
(devConfigTime 1)

cCN(7)	Signifies a configuration change or a software		H 7 ± Warning trap
	upgrade.

cCNTrapEnable	Use to enable or disable the configuration		H 1 ± Disable trap
(router 28)	change trap.		H 2 ± Enable trap
			H 2 ± Enable trap

C-16

August 2000

6371-A2-GB20-10

Image 88

Paradyne Routers manual Configuration MIB, Factory1-to-active8

Contents

HOTWIRE DSL Routers Copyright E 2000 Paradyne Corporation All rights reserved Contents Configuring the DSL Router Monitoring the DSL Router Index About This Guide Document Purpose and Intended Audience Document Summary Section Description Product-Related Documents Document Number Document Title Document Conventions Syntax Translation What is a Hotwire DSL Router? Introduction to Hotwire DSL RoutersDSL Technologies Supported Typical DSL Router System Network Access Provider NAPOptional Hotwire DSL Router Features IP routing with Service Subscriber Access Control to the DSL Router Accessing the DSL RouterLevels of Access Changing Access Session Levels Local Console AccessAdmin enable Show console CUSTOMER#. Type configure terminal and press Enter Setting Up the New Users LoginInvalid Characters Value Ascii Hex Translation Telnet Access Determining the Current Access LevelDetermining the Available Commands Local console disabled by conflict Exiting from the System Using the List CommandChanging the System Identity Manually Logging Out If you are accessing the DSL router ThenAutomatically Logging Out Overview of DSL Router Configuration Configuring the DSL RouterInterfaces for the DSL Router Service Domain IP Address Assignments Ethernet and DSL Interface Identifiers Unnumbered DSL Interface Numbered DSL InterfaceSimplified Network Topology IP Routing Network Considerations Address Resolution Protocol ARP Proxy ARP Basic NAT Network Address Translation NATNetwork Address Port Translation Napt IP Options Processing Dynamic Host Configuration Protocol Dhcp ServerApplications Supported by NAT Dhcp Relay Agent IP Filtering SecurityLand Bug/Smurf Attack Prevention Routed Network Model Standard mode Routed vs. Bridged PDUs DSL Router Configuration Examples Configuration Examples Basic Configuration Example Customer Premises CP Basic NAT Configuration Example NAT Mapping Public IP Addresses Private IP Addresses Napt Configuration Example Napt Mapping Public IP Addresses Private IP Addresses Core Router 155.1.3.253 Console Port Connection Dhcp Relay with Proxy ARP Configuration Example Dhcp Server with Basic NAT Configuration Example Public IP Addresses for Basic NAT Private IP Addresses Downstream Router Configuration Example Monitoring the DSL Router Detecting ProblemsWhat to Monitor Status of Interfaces Show interfaceShow interface eth1 dsl1 ± Ethernet Link up down Show statistics Interface StatisticsShow statistics eth1 dsl1 ip Clearing Statistics List of Discard ReasonsClear statistics eth1 dsl1 ip Discard Reasons for the Ethernet Interface eth1 1 Discard Reasons for the Ethernet Interface eth1 2 Discard Reasons for the DSL Interface dsl1 1 Discard Reasons for the DSL Interface dsl1 2 Discard Reasons for IP Diagnostics and Troubleshooting Diagnostics and Troubleshooting OverviewAlarms Inquiry Show alarms Syslog enable disable System LogShow syslog Syslog ip ip-addr Syslog Events Syslog level levelShow log number Syslog Messages 1 Level Description Event Syslog Messages 2 Level Description Event Syslog Message DisplayReporting Ping Ping Test ResultsPing reply x.x.x.x bytes of data=nn Ping reply x.x.x.x Request Timed OUT TraceRoute Test Results TraceRouteX.x Command Line Interface Command Line Interface Feature Navigation Command RecallDocument Conventions Command Line Interface Commands Configuration Control CommandsRFC 1483 Encapsulation Ethernet Frame Format Interface and Service Domain IP Address Delete eth1ifn dsl1ifn IP Routing TableIp route create dest-ipdest-mask next-hop-ip remote Ip route purge ARP Table Proxy ARP Nat basic enable Nat napt enableNat timeout time Nat basic address ip-addrip-mask Nat basic delete private-ip Nat napt delete udp tcp port Nat disable Dhcp server enable disableDhcp Server Nat purge Dhcp Relay Agent IP multicast enable disable IP processing enable disableTrap disable enable name of trap IP Packet Processing Show config Show Command OutputsNAT disabled or NAT enabled basic NAT Napt Show arp timeout NAT timeout xx minutes NAT basic mappingsShow ip route ip-address Show arp Show traps Show NAT naptShow dhcp server Show alarms Show syslog Show log # Show Dhcp relayShow interface Show statistics Sample show dhcp relay display Configuration Defaults Command Line Shortcuts Configuration Default Settings Paradyne Abc123Bytes Customer Command Line Input Shortcuts Table B-2. Command Line Input Shortcuts 1 Table B-2. Command Line Input Shortcuts 2 Table B-2. Command Line Input Shortcuts 3 Show interface dsl1 eth1 Configuration Defaults & Command Line Shortcuts Snmp Overview Traps & MIBsTraps Overview DSL Router Traps Variable Binding MIBs Overview Standard MIBsMIB II RFC System Group Ssssssssssss Boot bb.bb.bb 2nd Boot xx.xx.xx DSP System Interfaces Group RFC InterfacesIfEntry Yy.yy.yy H/W Releasezzz CCA part numberº IfOperStatus Specifies the current DSL interface Extension to Interfaces Table RFC Table C-5. IP Group Objects 1 Description Setting/ContentsIP Group RFC Table C-5. IP Group Objects 2 Description Setting/Contents IP Cidr Route Group RFC Transmission Group IpCidrRouteEntry 11 ± Snmp Group Ethernet-Like MIB RFC Paradyne Enterprise MIBs Device Control MIBNoOp1 Active1 Device Diagnostics MIB ApplpingTestEntry Traceroute ApplTracerouteResultsEntry ConfigureAppTracerouteResultsEntry DevStatus1 Health and Status MIBDevStatus Configuration MIB Factory1-to-active8 Interface Configuration MIB PdnInetIpAddressTableEntryPrimary Secondary Dhcp MIB DSL Endpoint MIB Syslog MIB DSL Router Terminal Emulation Accessing the List Command OutputDSL Router Terminal Emulation Terminal Emulation Programs Index Numbers IN-2 IN-3