Show NAT napt, Show traps, Show dhcp server | Paradyne Routers

Command Line Interface

show NAT napt

Sample show NAT napt display:

NAT NAPT ± { disabled enabled }

NAT NAPT ± public IP-address: x.x.x.x

NAT timeout: xx minutes

NAT NAPT mappings:
private-ip	private-port	mapped-port	protocol
x.x.x.x	xxxx	xxxx	{ udp tcp }

show traps

Sample show traps display: warmstart { disabled enabled } authen fail { disabled enabled } selftest { disabled enabled } devfail { disabled enabled } test start { disabled enabled } test stop { disabled enabled } ccn { disabled enabled }

link up { disabled enabled } link down { disabled enabled }

For additional information, refer to Appendix C, Traps & MIBs.

show dhcp server

Displays the DHCP relay's current status and configuration.

Minimum access level: Administrator

Sample show dhcp server display:

DHCP server { disabled enabled }

DHCP server ± router ip-addr:x.x.x.x

DHCP server ± name: domain name.com

DHCP server ± nameserver ip-addr:x.x.x.x

DHCP server ± address range:

lower ip-addr	x.x.x.x
upper ip-addr	x.x.x.x

DHCP server ± subnet mask: x.x.x.x

DHCP server ± leasetime:

minimum xxxx minutes maximum xxxx minutes

DHCP server bindings:
ip-addr	MAC addr	Leasetime (min.)
x.x.x.x	xx:xx:xx:xx:xx:xx	nnnn

6371-A2-GB20-10

August 2000

A-15

Image 65

Paradyne Routers manual Show NAT napt, Show traps, Show dhcp server

Contents

HOTWIRE DSL Routers Copyright E 2000 Paradyne Corporation All rights reserved Contents Configuring the DSL Router Monitoring the DSL Router Index Document Purpose and Intended Audience About This Guide Section Description Document Summary Document Number Document Title Product-Related Documents Syntax Translation Document Conventions DSL Technologies Supported Introduction to Hotwire DSL RoutersWhat is a Hotwire DSL Router? Optional Network Access Provider NAPTypical DSL Router System IP routing with Hotwire DSL Router Features Service Subscriber Levels of Access Accessing the DSL RouterAccess Control to the DSL Router Local Console Access Changing Access Session LevelsAdmin enable Show console Invalid Characters Value Ascii Hex Translation Setting Up the New Users LoginCUSTOMER#. Type configure terminal and press Enter Determining the Current Access Level Telnet AccessDetermining the Available Commands Local console disabled by conflict Changing the System Identity Using the List CommandExiting from the System Automatically Logging Out If you are accessing the DSL router ThenManually Logging Out Interfaces for the DSL Router Configuring the DSL RouterOverview of DSL Router Configuration Ethernet and DSL Interface Identifiers Service Domain IP Address Assignments Simplified Network Topology Numbered DSL InterfaceUnnumbered DSL Interface Network Considerations IP Routing Proxy ARP Address Resolution Protocol ARP Network Address Port Translation Napt Network Address Translation NATBasic NAT Applications Supported by NAT Dynamic Host Configuration Protocol Dhcp ServerIP Options Processing Dhcp Relay Agent Land Bug/Smurf Attack Prevention SecurityIP Filtering Routed vs. Bridged PDUs Routed Network Model Standard mode Configuration Examples DSL Router Configuration Examples Customer Premises CP Basic Configuration Example NAT Mapping Public IP Addresses Private IP Addresses Basic NAT Configuration Example Napt Mapping Public IP Addresses Private IP Addresses Napt Configuration Example Core Router 155.1.3.253 Console Port Connection Dhcp Relay with Proxy ARP Configuration Example Public IP Addresses for Basic NAT Private IP Addresses Dhcp Server with Basic NAT Configuration Example Downstream Router Configuration Example What to Monitor Detecting ProblemsMonitoring the DSL Router Show interface Status of InterfacesShow interface eth1 dsl1 ± Ethernet Link up down Show statistics eth1 dsl1 ip Interface StatisticsShow statistics List of Discard Reasons Clearing StatisticsClear statistics eth1 dsl1 ip Discard Reasons for the Ethernet Interface eth1 1 Discard Reasons for the DSL Interface dsl1 1 Discard Reasons for the Ethernet Interface eth1 2 Discard Reasons for IP Discard Reasons for the DSL Interface dsl1 2 Diagnostics and Troubleshooting Overview Diagnostics and TroubleshootingAlarms Inquiry Show alarms System Log Syslog enable disableShow syslog Syslog ip ip-addr Syslog level level Syslog EventsShow log number Syslog Messages 1 Level Description Event Reporting Syslog Message DisplaySyslog Messages 2 Level Description Event Ping Test Results PingPing reply x.x.x.x bytes of data=nn Ping reply x.x.x.x Request Timed OUT X.x TraceRouteTraceRoute Test Results Command Line Interface Feature Command Line Interface Document Conventions Command RecallNavigation Configuration Control Commands Command Line Interface CommandsRFC 1483 Encapsulation Ethernet Frame Format Interface and Service Domain IP Address Ip route create dest-ipdest-mask next-hop-ip remote IP Routing TableDelete eth1ifn dsl1ifn Ip route purge Proxy ARP ARP Table Nat napt enable Nat basic enableNat timeout time Nat basic address ip-addrip-mask Nat napt delete udp tcp port Nat basic delete private-ip Dhcp server enable disable Nat disableDhcp Server Nat purge Dhcp Relay Agent IP processing enable disable IP multicast enable disableTrap disable enable name of trap IP Packet Processing NAT disabled or NAT enabled basic NAT Napt Show Command OutputsShow config NAT timeout xx minutes NAT basic mappings Show arp timeoutShow ip route ip-address Show arp Show dhcp server Show NAT naptShow traps Show Dhcp relay Show alarms Show syslog Show log #Show interface Show statistics Sample show dhcp relay display Configuration Default Settings Configuration Defaults Command Line Shortcuts Abc123 ParadyneBytes Customer Table B-2. Command Line Input Shortcuts 1 Command Line Input Shortcuts Table B-2. Command Line Input Shortcuts 2 Show interface dsl1 eth1 Table B-2. Command Line Input Shortcuts 3 Configuration Defaults & Command Line Shortcuts Traps Overview Traps & MIBsSnmp Overview Variable Binding DSL Router Traps Standard MIBs MIBs OverviewMIB II RFC System Group System Ssssssssssss Boot bb.bb.bb 2nd Boot xx.xx.xx DSP Interfaces Interfaces Group RFCIfEntry Yy.yy.yy H/W Releasezzz CCA part numberº IfOperStatus Specifies the current DSL interface IP Group RFC Table C-5. IP Group Objects 1 Description Setting/ContentsExtension to Interfaces Table RFC IP Cidr Route Group RFC Table C-5. IP Group Objects 2 Description Setting/Contents IpCidrRouteEntry 11 ± Transmission Group Ethernet-Like MIB RFC Snmp Group Device Control MIB Paradyne Enterprise MIBsNoOp1 Active1 Device Diagnostics MIB Traceroute ApplpingTestEntry AppTracerouteResultsEntry ConfigureApplTracerouteResultsEntry DevStatus Health and Status MIBDevStatus1 Factory1-to-active8 Configuration MIB PdnInetIpAddressTableEntry Interface Configuration MIBPrimary Secondary Dhcp MIB DSL Endpoint MIB Syslog MIB DSL Router Terminal Emulation Accessing the List Command OutputDSL Router Terminal Emulation Terminal Emulation Programs Numbers Index IN-2 IN-3