Completing the installation | Patton electronic 2616RC instruction

Model 2616RC T-DAC User Manual	5 • Troubleshooting and maintenance

Completing the installation

This section verifies that the Model 2616RC is fully operational.

1.Verify that the green POWER LED is lit. If the POWER LED is flashing green, refer to Chapter 5, “Trou- bleshooting and maintenance” on page 60.

2.Verify that the WAN LED illuminates, indicating that the Model 2616RC is synchronizing with the T1/E1 signal.

3.Verify that after 5 seconds, the WAN LED begins flashing, indicating that the Model 2616RC is satisfied with the quality of the T1/E1 signal.

4.Verify that after 10 seconds, the WAN LED extinguishes, indicating that the Model 2616RC is satisfied with the network signal and that the link is ready for use.

5.Verify that the green Ethernet LED is either flashing (indicating link status is nominal for the front Ether- net port) or on solid (indicating that link status is nominal for at least one of the Ethernet backplane con- nections).

The Model 2616RC is operational.

Maintenance

71

Image 71

Patton electronic 2616RC user manual Completing the installation

Contents

T1/E1 TDM-Digital Access Concentrator T-DAC Patton Electronics Company, Inc Summary Table of Contents Contents Operation and shutdown Compliance information List of Figures Model 2960 RAS Getting Started Guide List of Tables Structure About this guideAudience Safety when working with electricity Precautions Mouse conventions Typographical conventions used in this documentGeneral conventions Introduction Chapter contents Model 2616RC T-DAC Model 2616RC T1/E1 T-DAC overview WAN Hardware overview Management services Power systemTemperature Physical dimensions MIB LED LED display Hardware installation Unpacking the Model 2616RC T-DAC DAC blades installationIntroduction Alignment/ESD pin and card handle Connecting the Ethernet ports Cable installation DB-9-to-RJ-45 cable diagram Pin Scsi to 8 RJ-45 connectors cable Connecting the T1/E1 WAN ports WAN cable‘s 68-pin Scsi connector SCSI-to-open-end WAN cable Pin Scsi to open end cable WAN cable’s 68 non-terminated twisted-pairs Punch-down block wiring Installing the WAN cable to a punch-down block Pin Scsi to 64-pin female Telco 10-3096TM68/64-6 Pin Scsi to open end, 6 foot cable 10-3096TM68-6-Obsolete Completing the hardware installation Configuring the T-DAC for operation Configuration prerequisites Connecting the DB9-RJ45 adapter with the included cable Initial configuration through the RS-232 control port Connection Description window Setting up the HyperTerminal or similar program session Configure your COM port settings as shown in , then click OK Login window Ethernet configuration window Using a browser to complete Model 2616RC configuration Home page overview Displaying the T-DAC 2616RC web administration pages Home page window panes Flash Configuring the default gateway Example Configuring the system clocking parameters System Clocking Configuration page, example For Clock Reference select secondary2 or slave3 DS0 Mapping Overview window Configuring the DS0 mapping Examples for configuring static connections Accessing the Line Interface Settings Configuring line settings and signaling for E1 T1/E1 Link Activity Ports 1 4 Configuring the E1 line interface settings From the Line Build Out pull-down menu select e1pulse1 E1 Alarms Present indicator Configuring line settings and signaling for T1 Line Type pull-down menu with dsx1ESF2 selected Configuring the T1 line settings From the Line Build Out pull-down menu select t1pulse0dB1 Alarm Card Information window Enabling/disabling the alarm card Backing up your configuration parameters Saving your configuration IMPORT/EXPORT Backing up the configuration store in flash memory Completing the installation Configuring the T-DAC for operation Operation and shutdown De-activating the Model 2616RC Activating the Model 2616RC Troubleshooting and maintenance Cited in De-activating the Model 2616RC on Power Fault analysis System DSX1 payload loop dsx1PayloadLoop T1/E1 port test modes Line Loop DSX1 line loop dsxLineLoop Calibration Periodic maintenanceMaintenance Exporting the current Model 2616RC configuration Maintenance Troubleshooting and maintenance Removing the defective Model 2616RC Importing a saved configuration Installing the replacement Model 2616RC Completing the installation Contacting Patton for assistance Returns for credit Warranty coverageOut-of-warranty service Contact information Shipping instructions Return for credit policyRMA numbers EMC Appendix a Compliance information Industry Canada Notice SafetyCompliance Radio and TV Interference Authorized European Representative FCC Part 68 Acta StatementCE Declaration of Conformity Introduction Not Used Introduction