WAN cable‘s 68-pin Scsi connector | Patton electronic 2616RC

Model 2616RC T-DAC User Manual			2 • Hardware installation

Figure 10. WAN cable‘s 68-pin SCSI connector

1.Connect the 68-pin SCSI connector (see figure 10) of the 6-foot WAN cable (see figure 9 on page 24) to the connector on the rear panel of the Model 2616RC.

2.Connect the WAN cable RJ-45 connectors (see figure 11) to the corresponding ports on a patch panel or local T1/E1 device.

Figure 11. RJ-45 plug

Table 4. RJ-45 plug pin-out

Description	Pin

Transmit pair (TX)	1
Transmit pair (TX)	2

Receive pair (RX)	4
Receive pair (RX)	5

Cable installation

25

Image 25

Patton electronic 2616RC user manual WAN cable‘s 68-pin Scsi connector

Contents

T1/E1 TDM-Digital Access Concentrator T-DAC Patton Electronics Company, Inc Summary Table of Contents Contents Operation and shutdown Compliance information List of Figures Model 2960 RAS Getting Started Guide List of Tables Audience About this guideStructure Safety when working with electricity Precautions General conventions Typographical conventions used in this documentMouse conventions Introduction Chapter contents Model 2616RC T-DAC Model 2616RC T1/E1 T-DAC overview WAN Hardware overview Temperature Power systemPhysical dimensions Management services MIB LED LED display Hardware installation Introduction DAC blades installationUnpacking the Model 2616RC T-DAC Alignment/ESD pin and card handle Connecting the Ethernet ports Cable installation DB-9-to-RJ-45 cable diagram Pin Scsi to 8 RJ-45 connectors cable Connecting the T1/E1 WAN ports WAN cable‘s 68-pin Scsi connector SCSI-to-open-end WAN cable Pin Scsi to open end cable WAN cable’s 68 non-terminated twisted-pairs Punch-down block wiring Installing the WAN cable to a punch-down block Pin Scsi to 64-pin female Telco 10-3096TM68/64-6 Pin Scsi to open end, 6 foot cable 10-3096TM68-6-Obsolete Completing the hardware installation Configuring the T-DAC for operation Configuration prerequisites Connecting the DB9-RJ45 adapter with the included cable Initial configuration through the RS-232 control port Connection Description window Setting up the HyperTerminal or similar program session Configure your COM port settings as shown in , then click OK Login window Ethernet configuration window Using a browser to complete Model 2616RC configuration Home page overview Displaying the T-DAC 2616RC web administration pages Home page window panes Flash Configuring the default gateway Example Configuring the system clocking parameters System Clocking Configuration page, example For Clock Reference select secondary2 or slave3 DS0 Mapping Overview window Configuring the DS0 mapping Examples for configuring static connections Accessing the Line Interface Settings Configuring line settings and signaling for E1 T1/E1 Link Activity Ports 1 4 Configuring the E1 line interface settings From the Line Build Out pull-down menu select e1pulse1 E1 Alarms Present indicator Configuring line settings and signaling for T1 Line Type pull-down menu with dsx1ESF2 selected Configuring the T1 line settings From the Line Build Out pull-down menu select t1pulse0dB1 Alarm Card Information window Enabling/disabling the alarm card Backing up your configuration parameters Saving your configuration IMPORT/EXPORT Backing up the configuration store in flash memory Completing the installation Configuring the T-DAC for operation Operation and shutdown De-activating the Model 2616RC Activating the Model 2616RC Troubleshooting and maintenance Cited in De-activating the Model 2616RC on Power Fault analysis System DSX1 payload loop dsx1PayloadLoop T1/E1 port test modes Line Loop DSX1 line loop dsxLineLoop Maintenance Periodic maintenanceExporting the current Model 2616RC configuration Calibration Maintenance Troubleshooting and maintenance Removing the defective Model 2616RC Importing a saved configuration Installing the replacement Model 2616RC Completing the installation Contacting Patton for assistance Out-of-warranty service Warranty coverageContact information Returns for credit RMA numbers Return for credit policyShipping instructions EMC Appendix a Compliance information Compliance SafetyRadio and TV Interference Industry Canada Notice CE Declaration of Conformity FCC Part 68 Acta StatementAuthorized European Representative Introduction Not Used Introduction