Connections and part names

!Wait until all connections between devices have been completed before connecting the AC adapter.

Be sure to turn off the power and unplug the AC adapter from the power outlet before making or changing connections between devices.

Refer to the operating instructions for the component to be connected.

!Only use the AC adapter included with this unit.

!Power to this unit is supplied by the AC adapter or by USB bus power.

This unit can be used by connecting it to a computer using a USB cable, even without connecting the AC adapter.

!Connect this unit and the computer directly using the included USB cable.

!A USB hub cannot be used.

Notes on running this unit with USB bus power

!When using this unit on USB bus power, supply power to the con- nected computer from the AC power supply. Do not run the com- puter on its battery.

!In cases like the ones below, the power may be insufficient and this unit may not operate on USB bus power.

—When the computer’s USB power supply capacity is insufficient.

—When other USB devices are connected to the computer.

If this unit does not operate on USB bus power, connect the included AC adapter.

!The following limitations apply when operating on USB bus power:

—The jog dial indicator will not light.

—The [MASTER OUT 1] (XLR output) channel is not output.

—The [MIC1], [MIC2] and [AUX IN] terminals cannot be used.

—The indicators are dimmer than when using the AC adapter. To use the unit without these limitations, connect the included AC adapter.

Connecting the input/output terminals

Front panel

Headphones

Microphone

To headphones

 

To microphone

Headphones

 

Microphone

 

cable

cord

 

 

 

 

MIC/AUXTHRU

 

PHONES

OFF ON

MIC 2

 

1 2 3

1PHONES jacks

Connect headphones here.

Both stereo phone plugs (Ø 6.3 mm) and stereo mini phone plugs (Ø 3.5 mm) can be used.

For details, see Monitoring sound with headphones on page 27.

!There are two input jacks, both a stereo phones jack and a mini phones jack, but do not use both simultaneously. If both are used simultaneously, when one is disconnected and/or connected, the volume of the other may increase or decrease suddenly.

10En

2MIC/AUX THRU selector switch

Set this to [ON] if you want to output the [MIC2] and [AUX] channels directly.

=Outputting the microphone and AUX sound directly (p.29)

3MIC2 terminal

Connect a microphone here.

=Using a microphone (p.28)

Rear panel

Component,

Portable

amplifier,

audio

powered speaker, etc.

device

To audio input

To audio output

terminals

terminals

 

1GND

R

L

R L

 

 

 

2 HOT

 

 

 

 

 

 

3 COLD

 

 

 

 

-12 dB -6 dB 0 dB R

L

R

L R

 

L

MIN MAX

 

 

MASTER ATT.

MASTER OUT1

MASTER OUT2

AUX IN

 

VOL

1

2

3

4

 

5

MASTER ATT. MASTER OUT 1 MASTER OUT2 AUX IN

VOL

 

 

 

 

USB ON OFF DC IN

 

 

 

 

 

 

To power outlet

 

Computer

 

 

ITCH

 

 

 

 

AC adapter

 

 

 

 

 

 

 

 

 

 

 

 

(included)

 

 

 

 

 

 

5 V

 

 

 

 

 

 

USB ON OFF DC IN

6 7 8 9 a

1MASTER ATT.

Sets the attenuation level of the sound output from the [MASTER1] terminal.

2MASTER OUT 1 terminals

Connect powered speakers, etc., here.

3MASTER OUT 2 terminals

Connect to a power amplifier, etc.

4AUX IN terminal

Connect to the output terminal of an external device (sampler, portable audio device, etc.)

5VOL control

Adjusts the audio level input to the [AUX IN] terminals.

6Kensington security slot

7 USB terminal

Connect to a computer.

!Connect this unit and the computer directly using the included USB cable.

!A USB hub cannot be used.