9FX CH SELECT control
Switches the channel to which the effect is applied.
=Using the effect function (p.29)
AMASTER LEVEL control
Adjusts the master sound level output.
BEFFECT SELECT control
Selects the type of effect.
=Using the effect function (p.29)
CPARAMETER control
Adjusts the parameters provided for the various effects (time, harmonics etc.).
=Using the effect function (p.29)
DHEADPHONES MIXING control
Adjusts the monitor volume balance between the sound of channels for which the headphones [CUE] button is pressed and the sound of [MASTER OUT 1] and [MASTER OUT 2].
=Monitoring sound with headphones (p.27)
ELEVEL/DEPTH control
Adjusts the quantitative parameter of the effect.
=Using the effect function (p.29)
FChannel level indicator
GFX ON/OFF button
Turns the effect on/off.
=Using the effect function (p.29)
HTAP button
The BPM used as the base value for the effect is calculated by the interval at which the button is tapped with a finger.
=Setting the BPM manually (p.29)
IC.F. REV indicator
Lights when the [C.F. REV] switch is set to [ON].
JFADER START switch
These turn the fader start function on/off.
=Starting playback using the fader (Fader Start) (p.28)
KCrossfader curve selector switch
This switches the crossfader curve characteristics.
=Selecting the crossfader curve characteristics (p.27)
LCrossfader
Switches between the audio output of the left and right decks.
=Outputting sound (p.27)
MC.F. REV switch
Reverses the deck to which the crossfader is assigned from right to left and vice versa.
=Using the crossfader reverse function (p.28)
NMaster level indicator
OChannel fader
Adjusts the sound level output from the various decks.
=Outputting sound (p.27)
PHEADPHONES LEVEL control
Adjusts the audio level output from the [PHONES] terminal.
QHeadphones CUE button
The sound of decks for which the headphones [CUE] button is pressed can be monitored over headphones.
=Monitoring sound with headphones (p.27)
REQ (HI, MID, LOW) controls
Boosts or cuts frequencies for the different channels.
=Equalization (p.27)
STRIM control
Adjusts the individual channel output gain.
=Outputting sound (p.27)
Do not pull on the channel fader and crossfader knobs with excessive | English | |
force. The knobs are not designed to be removed. Pulling the knobs | ||
| ||
strongly may result in damaging the unit. |
|
| MIC1 |
|
|
|
|
|
| EQ |
|
|
|
| LEVEL | LOW |
|
| MID | HI | |
|
| TALK |
|
|
|
|
|
|
|
| OFF | ON OVER |
|
|
|
|
|
|
|
MIC1 |
|
| MIN | MAX | MIN | MAX | MIN | MAX MIN | MAX |
| 1 |
| 2 |
| 3 |
|
| 4 | |
MIC2 / AUX |
|
|
| EQ |
|
|
|
| |
| LEVEL | LOW |
| MID |
| HI | INPUT | ||
| TALK |
|
|
|
|
|
| ||
OFF ON |
|
|
|
|
|
| SELECT | ||
| OVER |
|
|
|
|
|
| MIC 2 | AUX |
| MIN | MAX | MIN | MAX MIN | MAX | MIN |
| MAX |
|
1OFF, ON, TALK OVER selector switch
Turns the microphone on/off.
=Using a microphone (p.28)
2LEVEL control
Adjusts the level of the output sound.
3EQ (HI, MID, LOW) controls
Boosts or cuts frequencies in order to change the quality of the sound.
4MIC2/AUX selector switch
Switches the audio input between the microphone and the external device.
![MIC2]: Selects the microphone connected to the [MIC2] terminal.
![AUX]: Selects the external device connected to the [AUX IN] terminals.
=Using a microphone (p.28)
=Using an external device (p.28)
Using the LAPTOP DOCKThe computer’s keyboard section can be stowed under this unit.
!Depending on the size of your (notebook) computer, the keyboard section may not fit in the LAPTOP DOCK.
!Install in such a way that the computer unit does not touch this unit.
!Install in such a way that the cables connected to the computer are not stuck under this unit.
Using with the feet removedThis unit’s two feet can be removed.
Use a Phillips screwdriver to remove the screws from the left and right feet (2 screws each).
DJ CONTROLLER
!The screws you have removed will be needed when mounting the feet. Be careful not to lose them. The feet cannot be properly mounted using other screws.
En 13