Pioneer VSX-D2011-G Fine Channel Delay, FINE CHANNEL DELAY should be, using the 5∞ buttons, 1 2 3

Fine Tuning Your System

FINE CHANNEL DELAY

The following steps show you how to adjust the delay level of your speakers more finely than in the NORMAL setup (see page 43). Adding a slight delay to some speakers is necessary to achieve proper sound depth, separation as well as an effective surround sound effect. Do this procedure if you want to try and get even finer surround sound.

The main difference with this setup method and the CHANNEL DELAY setup method in NORMAL setup is that here the test tone sounds from a reference channel and you use that to measure the target speaker (that is, the speaker whose level you want to adjust).

1	2	3	4	Follow steps 1-5 on page 95, if necessary, to get to the
DIMMER	LOUDNESS	TONE	EFFECT/CH SEL
SIGNAL SEL	DNR BASS/TREBLE +			starting point mentioned here.
5	6	7	8
VIDEO SEL	HI-BIT	+10	– DISC
9	0		ENTER	1	FINE CHANNEL DELAY should be
MENU			TOP MENU
	DIRECT ACCESS SEARCH MODE
SYSTEM SETUP			GUIDE		selected, if it isn’t use the 5∞
TUNER EDIT			EXIT	1-6
			TRACK
	ENTER
AUDIO			RETURN		buttons to select and press ENTER.
MPX	TEXT ON	RF ATT	DISP MODE
¶	8		SUB TITLE
TUNING –	BAND		TUNING +
1	3		¡	2	Use the 5∞ buttons to adjust the
4	7	CLASS	¢
STATION –	TEXT OFF		STATION +
CHANNEL–			CHANNEL+		distance of the FRONT L channel.
1-6
					Press ENTER.
					Test tones will be output.
					This channel will be the target reference which you
					use to measure the other channels.

STANDBY/ON
		STANDBY			3	Use the 5∞ buttons to select the
MOVIE	MUSIC	ENTER
	MULTI JOG					channel you want to adjust. Press
		MULTI JOG CONTROL SIGNAL HI-BIT		SB CH	BAND
		SET UP	RETURN SELECT HI-SAMPLING	MODE		ENTER.
		PHONES	TONE CONTROL
			SPEAKERS TONE BASS/TREBLE
						Test tones will be output for the channel you want to
						adjust and a reference channel.
						Listen to the reference channel and use to measure
						the target channel.

1

2

3

Expert

[Crossover Network		]
[Fine Channel Level		]
[	Fine Channel Delay	]
	[Acoustic Cal EQ	]
[Bass Peak Level		]
[D-Range Control		]
[Exit		]

Fine Channel		Delay
Front L			[		]
				3 . 0 m
Fine Channel		Delay
STD:Front	L			3 . 0 m
Front			[			]
	R			3 . 0 m
Center		L	[	3 . 3 m		]
Surround			[	2 . 4 m ]
Surround		R	[	2 . 1 m ]
SurrBack		L	[	1 . 8 m ]
SurrBack		R	[	1 . 5 m ]
Subwoofer			[	4 . 0 m ]
[Exit ]

4Adjust the distance of each channel

using the 5∞ buttons.

Listen to the reference channel and use it to measure the target channel. Stand facing the two speakers with

your arms outstretched pointing at each speaker. Try

to make the two tones sound

as if they are arriving simultaneously at a postion slightly in front of you and between your arm span. The distance can be set within a range of 0.1 m to 9.0 m in 0.1 m steps.

When you press ENTER you will automatically go to the next channel.

5Press ENTER to select a new channel. Repeat step 4 for every channel.

6

98

Fine Channel				Delay
STD:Front			L			3 . 0 m
Front			R		[	3 . 0 m ]
Center				L	[	3 . 3 m ]
Surround					[	2 . 4 m ]
Surround				R	[	2 . 1 m ]
SurrBack				L	[	1 . 8 m ]
SurrBack				R	[	1 . 5 m ]
Subwoofer					[	4 . 0 m ]
[	Exit	]

If you want to change a setting before proceeding Use the 5∞ buttons to go back to the channel you want to adjust and press ENTER. Then follow step 3.

6When done select EXIT (if it's not

already selected) and press ENTER.

Next, if you want, proceed to ACOUSTIC CAL EQ.

En