Pioneer VSX-D3S warranty Appendix a Specifications, Channel mode

APPENDIX A: SPECIFICATIONS

Amplifier Section

<2-channel mode>

Continuous average power output of 130 watts* per channel, min., at 8 ohms, from 20 Hz to 20,000 Hz with no more than 0.05 %** total harmonic distortion.

<5-channel mode>

Continuous average power output of 100 watts* per channel, min., at 8 ohms, from 20 Hz to 20,000 Hz with no more than 0.8 %** total harmonic distortion.

*Measured pursuant to the Federal Trade Commission’s Trade Regulation rule on Power Output Claims for Amplifiers.

**Measured by Audio Spectrum Analyzer.

Continuous Power Output	100 W + 100 W (1 kHz, 0.8 %, 8 Ω)
Front
Center		100 W (1 kHz, 0.8 %, 8 Ω)
Rear	100 W + 100 W (1 kHz, 0.8 %, 8 Ω)
[Multi-voltage model]
Continuous Power Output (DIN)
Front (1 kHz, T.H.D. 1 %, 8 Ω)		150 W + 150 W
Dynamic Power (2 Ω/4 Ω)		275 W/220 W
Input (Sensitivity/Impedance)		2.8 mV/47 kΩ
PHONO MM
CD, TAPE 1, TAPE 2, LD,	.............................	200 mV/47 kΩ
VCR 1, VCR 2, VIDEO, TV/SAT
Phono Overload Level (T.H.D. 0.1%, 1 kHz)
PHONO MM		80 mV
Frequency Response		20 Hz to 20,000 Hz ± 0.3 dB
PHONO MM
CD, TAPE 1, TAPE 2, LD, VCR 1,
VCR 2, VIDEO, TV/SAT		+0
		5 Hz to 100,000 Hz –3dB
Output (Level/Impedance)		200 mV/2.2 kΩ
TAPE 1 REC, TAPE 2 REC
VCR 1 OUT, VCR 2 OUT		200 mV/2.2 kΩ
Tone Control		± 8 dB (150 Hz)
BASS
TREBLE		± 8 dB (10 kHz)
SUPER BASS		0 ~ +8 dB (80 Hz, variable)
Signal-to-Noise Ratio (IHF, short circuited, A network)
PHONO MM		76 dB
CD, TAPE 1, TAPE 2, LD,
VCR 1, VCR 2, VIDEO, TV/SAT		98 dB
Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]
PHONO MM		77 dB
CD, TAPE 1, TAPE 2, LD,
VCR 1, VCR 2, VIDEO, TV/SAT		80 dB
VIDEO Section
Input (Sensitivity/Impedance)	...........................	1 Vp-p/75 Ω
VCR 1, VCR 2, LD, VIDEO, TV/SAT
Output (Level/Impedance)		1 Vp-p/75 Ω
VCR 1, VCR 2, MONITOR
Frequency Response
VCR 1, VCR 2,
LD, VIDEO = MONITOR		+0
		5 Hz to 10 MHz –3dB
Signal-to-Noise Ratio		55 dB
Cross Talk		55 dB
AC-3 Input Section
AC-3 • RF (LD)		1
AC-3 • DIGITAL (TV/SAT)		1

36

FM Tuner Section
Frequency Range		87.5 MHz to 108 MHz
Usable Sensitivity	Mono: 11.2 dBf, IHF (1.0 ∝V/75 Ω)
50 dB Quieting Sensitivity		Mono: 16.8 dBf
		Stereo: 38.6 dBf
Signal-to-Noise Ratio		Mono: 80 dB (at 65 dBf)
		Stereo: 76 dB (at 85 dBf)
Distortion		Stereo: 0.3 % (1 kHz)
Alternate Channel Selectivity		65 dB (400 kHz)
Stereo Separation		45 dB (1 kHz)
		+0.5
Frequency Response		30 Hz to 15 kHz ( –2.0) dB
Antenna Input		300 Ω balanced
		75 Ω unbalanced
AM Tuner Section
Frequency Range	531 kHz to 1,602 kHz (9 kHz step)
	530 kHz to 1,700 kHz (10 kHz step)
Sensitivity (IHF, Loop antenna)	.....................................	300 ∝V/m
Selectivity		25 dB
Signal-to-Noise Ratio		50 dB
Antenna		Loop antenna
Miscellaneous
Power Requirements
U.S. and Canadian models		AC 120 V, 60 Hz
Multi-voltage model	AC 110 V/120 -127 V/220 V/240 V
		(Switchable), 50/60 Hz
Power Consumption
U.S. and Canadian models		455 W, 700 VA
Multi-voltage model		1175 W
In Standby Condition		5 W
AC Outlets
U.S. and Canadian models
SWITCHED x 2		TOTAL 100 W (0.8 A) MAX
UNSWITCHED x 1		100 W (0.8 A) MAX
Multi-voltage model
SWITCHED x 2		TOTAL 100 W MAX
UNSWITCHED x 1		100 W MAX
Dimensions	420 (W) x 162 (H) x 425 (D) mm
16-9/16 (W) x 6-3/8 (H) x 16-3/4 (D) in
Weight (without package)
U.S. and Canadian models		15.0 kg (33 lb 1 oz)
Multi-voltage model		15.2 kg (33 lb 8 oz)
Furnished Parts
FM T-type Antenna		1
AM Loop Antenna		1
Dry Cell Batteries (size “AA” IEC R6P)		........................................ 2
Remote Control Unit		1
Main-Repeater		1
Mini-Repeater		1
Operating Instructions		1
NOTE:
Specifications and the design are subject to possible
modifications without notice, due to improvements.

<ARB7050>