Pioneer VSX-D3S warranty Speaker System Connections, Speaker cord connection

CONNECTIONS

SPEAKER SYSTEM CONNECTIONS

NOTE:

Use speakers with an impedance of 8 Ω to 16 Ω.

When connecting speakers to the FRONT SPEAKERS B terminals, the procedure is the same as that used for connecting speakers to the FRONT SPEAKERS A terminals.

NOTE:

÷Do not allow any of the cord’s conductors to protrude from the terminals or touch any other conductors. Malfunctioning or breakdowns may occur when conductors come into contact with each other.

÷If you have one pair of speakers only, connect it to front speaker terminals A or B.

÷Be sure to connect single rear speaker to the L channel.

You can set this unit to match the requirements and specifications of your stereo system’s speakers (whether or not center speaker(s), rear speakers or a sub-woofer are used, speaker size, etc.) to assure optimum sound quality. Before using, perform settings in the SPEAKER MODE (refer to page 29).

NOTE:

This unit does not feature conventional switching between NORMAL/WIDE/PHANTOM center modes.

Speaker cord connection

SPEAKER I+II SELECTOR

in) (3/8

10mm

+
2
1	3
3	2

I ONLY

1 Push the lever forward.

1

1 Loosen cap.

2 Insert the cord into the hole.

2 Insert wire.

SUB WOOFER

CENTER

SELECTOR

TWO VOLTAGE

SELECTORS

3 Pull the lever back.

3 Tighten cap.

SPEAKER

PRE

PRE

110V

OUT

OUT

I+II

SPEAKER

120～127V

IMPEDANCE

+

CENTER

8Ω～16Ω

／SPEAKER

SPEAKERS

CAUTION:

I ONLY

THE POWER

220V

240V

Connecting Two Center Speakers for Dual Center

SUPPLY CORD SHOULD

220V

SELECTOR.

BE DISCONNECTED

240V 110V

120-127V

BEFORE CHANGING

THE VOLTAGE

There are two sets of terminals for center speakers on the main

–

MANUAL

+

I

II

SEE

A

INSTRUCTION

unit, so you can connect two speakers. When you cannot install

+

R

L

SPEAKERS

SWITCHED

–

a speaker under or behind your TV, installing speakers either

FRONT

TOTAL 100W MAX

–

SPEAKERS

100W MAX

side of the TV as a center speaker is just as effective.

R

L

REAR

R

L

B

CAUTION:

SPEAKER IMPEDANCE

8Ω～16Ω／SPEAKER

DO NOT CONNECT

TV SET CR MONITOR.

AC OUTLETS

When the SPEAKER SELECTOR switch is in the “Ι + ΙΙ” position,

–

+

–

+

Illustration

be sure to connect two speakers. If only one speaker is connected,

shows Multi-

there will be no sound.

voltage model.

Both speaker systems should have an impedance of 4 Ω to 16 Ω.

FRONT

+ – CENTER

	+
+	–
	–

SUB WOOFER	CENTER	SPEAKER	TWO VOLTAGE SELECTORS
PRE	PRE	SELECTOR
			110V
OUT	OUT	SPEAKER	120～127V
	I+II	IMPEDANCE
	CENTER	8Ω～16Ω
		／SPEAKER

SPEAKERS

				CAUTION:
			I ONLY	THE POWER			220V	240V
				SUPPLY CORD SHOULD		220V
				BE DISCONNECTED		240V	110V	120-127V
				BEFORE CHANGING
				THE VOLTAGE
				SELECTOR.
I	II	SEE		A
		INSTRUCTION
		MANUAL
			R		L
						SWITCHED
				FRONT		TOTAL 100W MAX
				SPEAKERS
R	L	REAR				UNSWITCHED
		SPEAKERS	R		L	100W MAX

B

CAUTION:

SPEAKER IMPEDANCE

SPEAKER SELECTOR

I+II

IONLY

8Ω～16Ω／SPEAKER

DO NOT CONNECT TV SET CR MONITOR.

AC OUTLETS

SP-A(L)

(L)

+–

+ –

SP-A(R)	–	+	Illustration shows
			Multi-voltage model.

(R)

+–

REAR

– + – +

NOTE:

Before connecting pin jacks, speaker cables and other jacks and cables, switch power to the unit OFF, and wait for about one hour. (When power is ON, the rear panel may become very hot.)

9

<ARB7050>