Power-Up Config, SMT Status, SMT Sel Toolset | Printronix SL5000r

QUICK SETUP Menu Items

Power-Up Config.

You can specify the Factory configuration or any one of the eight possible saved configurations as the power-up configuration.

The default is Factory.

SMT: Status

This menu appears only if an RFID encoder is installed. Refer to “Software Migration Tools (SMT)” in the RFID Labeling Reference Manual.

•Disabled.The printer disables the use of the Software Migration Tools.

•Enabled. The printer enables the use of the Software Migration Tools.

SMT: Sel Toolset

This menu appears only if an RFID encoder is installed. Refer to “Software Migration Tools (SMT)” in the RFID Labeling Reference Manual.

•Toolset [1]. SMTs for PGL emulation.

•Toolset [2]. SMTs for PPI/ZGL emulation.

•Toolset [3] and Toolset [4]. Reserved for internal use and future design.

SMT: Select Tool

This menu appears only if an RFID encoder is installed. Refer to “Software Migration Tools (SMT)” in the RFID Labeling Reference Manual.

•EPC, GTIN, UPCA, EAN8, EAN13, and UCC128. SMTs displayed if Toolset [1] is selected under SMT: Sel Toolset.

•zEPC, zGTIN, zUPCA, zEAN8, zEAN13, and zUCC128. SMTs displayed if Toolset [2] is selected under SMT: Sel Toolset.

NOTE: Undocumented options are reserved for internal use and future design.

49

Image 49

Printronix SL5000r manual Power-Up Config, SMT Status, SMT Sel Toolset, SMT Select Tool

Contents

Quick Setup Guide Page Page Definitions Software License Agreement Termination of License Agreement Canada Communication Notices Declaration Of Conformity CE Notice European Union Trademark Acknowledgements Taiwan Lithium Battery Warning Table of Contents Table of Contents Unpacking The Printer Unpacking And Installing The Printer Removing The Internal Packing Material Unpacking And Installing The Printer Installation Installation Power Switch Controls And IndicatorsControls And Indicators Control Panel Liquid Crystal JOB Select Key Control Panel Keys Control Panel Down Key in Menu mode Menu Key Loading Media And Ribbon Loading Media And Ribbon Loading Roll Media Loading Roll Media Media Roll Media Hanger Guide Media Width Media Damper Loading Roll Media Lower Media Sensor Fixed Guide Media Width Notch Loading Ribbon Loading Ribbon Loading Media And Ribbon Printhead Pressure Adjustment Printing AdjustmentsPrinthead Pressure Block Adjustments Left Pressure Block Positioning The Media Sensors Printing Adjustments Feed Positioning The Media Sensors Running Auto Calibrate Calibrating The PrinterCalibrating The Printer Running Auto Calibrate Making a Media Profile Printout Making a Media Profile Printout Gap Sensing 255 191 127 Advanced Gap Sensing Paper Out075 Changing The Active IGP Emulation Configuring The Printer Quick Setup Menu Quick Setup Menu Cont. from previous Print Mode Quick Setup Menu ItemsPrint Intensity Print Speed Media Handling Quick Setup Menu Items Label Length Paper Feed ShiftLabel Width Ver Image Shift Orientation Hor Image Shift EdgetopTheof isimagethe thetoparallelleft theofedgemedia Quick Setup Menu Items Gap Sensing for Smart Labels Gap/Mark Sensor Auto Calibrate Validator Funct Save ConfigActive IGP Emul SMT Status Power-Up ConfigSMT Sel Toolset SMT Select Tool Auto Save Configuration Saving The ConfigurationSaving The Configuration Loading a Saved Configuration Selecting The Power-Up Configuration Printing a Configuration Printing a Configuration Run a Barcode Demo Test General Cleaning CleaningCleaning The Printhead, Platen Roller, Media Sensors Exterior Media Sensor Cleaning Platen Roller CleaningMedia Damper Cleaning Cleaning The Printhead, Platen Roller, And Media Sensors Cleaning Upper Media Sensor From Printhead Heating Elements Repacking The Printer Repacking The Printer Media Cover window side Straps not supplied Printronix Customer Support Center Contact InformationPrintronix Supplies Department Contact Information Corporate Offices For More InformationCorporate Offices Page Page 178423-001