Chimney Termination Requirements | Quadra-Fire 7046-137C specification

R

2700-I ACC Wood Insert

D. Locating Your Stove & Chimney

Location of the appliance and chimney will affect perfor- mance. As shown in Figure 27.1 the chimney should:

•Install through the warm space enclosed by the build- ing envelope. This helps to produce more draft, espe- cially during lighting and die down of the fire.

•Penetrate the highest part of the roof. This minimizes the affects of wind turbulence and down drafts.

•Consider the appliance location in order to avoid floor and ceiling attic joists and rafters.

•Locate termination cap away from trees, adjacent structures, uneven roof lines and other obstruc- tions.

Your local dealer is the expert in your geographic area and can usually make suggestions or discover solutions that will easily correct your flue problem.

Recommended Recommended

Location Location

Marginal

Location

Location

Not

Recommended

Location NOT

Recommended

Windward

Outside Termination Cap

Leeward

Multi-level Roofs

Figure 27.1

E. Chimney Termination Requirements

Follow manufacturer’s instructions for clearance, securing flashing and terminating the chimney.

•Must have an approved and Listed cap

•Must not be located where it will become plugged by snow or other material

•Must terminate at least 3 feet (91cm) above the roof and at least 2 feet (61cm) above any portion of the roof within 10 feet (305cm).

•Must be located away from trees or other structures

Notice: Locating the appliance in a basement or in a location of considerable air movement can cause intermittent smoke spillage from appliance. Do not locate appliance near

•Frequently open doors

•Central heat outlets or returns

NOTICE:

•Chimney performance may vary.

•Trees, buildings, roof lines and wind conditions affect performance.

•Chimney height may need adjustment if smoking or overdraft occurs.

December 15, 2009

7046-137C

Page 27

Image 27

Quadra-Fire 7046-137C warranty ACC Wood Insert Locating Your Stove & Chimney, Chimney Termination Requirements

Contents

Hot glass will cause burns ACC Wood Insert Serial Number ACC Wood Insert Table of Contents ACC Wood Insert Warranty Policy ACC Wood Insert Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Listing and Code Approvals Your Wood Appliance Operating Instructions Seasoned Wood ACC Wood Insert Fire SafetyCombustible/Non-combustible Materials Overfiring Final Stage ACC Wood Insert Burning ProcessKindling or First Stage Second Stage Start-Up Air Control Manual Timer Over-RideACC Wood Insert Automatic Combustion Control ACC Air Controls Burn Rates and Operating Efficiency Incorrect Baffle and Blanket Positions Correct Baffle and Blanket Positions ACC Wood Insert Building a Fire Do not USE Chemicals or Fluids to Start a Fire ACC Wood Insert Wood Fuel Blower Operating Instructions Frequently Asked Questions ACC Wood Insert Clear SpaceOpacity Smoke Disposal of Ashes Maintenance and ServiceChimney and Chimney Connector Inspection/Cleaning Cleaning Plated Surfaces ACC Wood Insert Glass Cleaning Inspect Firebrick Cont’dInspect Firebrick Baffle & Blanket Placement Start Fire Problems Possible Cause Solution Troubleshooting Guide Glass Replacement Snap Disc Replacement Service Parts Replacement Shock Risk ACC Wood Insert Blower Replacement Baffle & Ceramic Blanket Removal ACC Wood Insert Door Handle Assembly ACC Wood Insert Tube Channel Assembly Replacement Design and Installation Considerations Getting StartedDraft ACC Wood Insert Negative Pressure Chimney Termination Requirements ACC Wood Insert Locating Your Stove & Chimney Flat Roof ACC Wood Insert Rule ACC Wood Insert Tools And Supplies Needed Inspect Appliance and ComponentsPre-Use Check List Appliance Dimensions Dimensions and Clearances SideWall Required Build On-Site Hearth Support AccessoryACC Wood Insert Zero Clearance Floor Protection Full Reline ACC Wood Insert Calculating Alternate Floor Protection Masonry Chimney Chimney SystemsVenting Systems Inspections ACC Wood Insert Masonry Chimney Cont’d ACC Wood Insert Metal Heat Circulating Masonry Prefabricated Metal Chimney36.1 ACC Wood Insert Prefabricated Metal Chimney Cont’d Securing Chimney ComponentsAltering the Fireplace ACC Wood Insert Zero-Clearance Fireplace Ovalizing Round Stainless Steel LinersChimney Height / Rise and Run Option Two Installation Instructions Outside Air Kit InstallationItems Needed for Installation not supplied Option One Installation Instructions Flue Adapter Leveling Legs Slide Top Installation Instructions ACC Wood Insert Surround & Trim Kit Installation Cont’d Instructions ACC Wood Insert Blower Cord Installation on Left Side ACC Wood Insert Zero Clearance Adjustable Trim Support Adjustable from 2 inches to 10 inchesShears, Measuring Tape, Gloves Mobile Home Installation Exploded Drawings Reference Materials Figure a Important this is Dated Information HOW to Order ACC Wood Insert Service Parts & Accessories Stocked At Depot Description Comments Part Number Stocked Description Comments Part NumberFasteners Date of Service Performed By Description of Service ACC Wood Insert Service And Maintenance Log Contact Information