Adjustable from 2 inches to 10 inches | Quadra-Fire 7046-137C

2700-I ACC Wood Insert		R
2700-I ACC Wood Insert
I. Zero Clearance Adjustable Trim Support,	EXPLODED VIEW OF SCISSORS
Adjustable from 2 inches to 10 inches
Part No. ADJSPT-3, size 3-1/2” x 48-1/2”
Included in Kit: (1) Trim Top, (1) Trim Front, (2) Trim Sides,		SCREWS ARE CIRCLED

Double-Sided Tape (already installed)
Tools Needed: Phillips Head Screwdriver, Sheet Metal	DOUBLE-SIDED TAPE	DOUBLE-SIDED TAPE
Shears, Measuring Tape, Gloves	Figure 44.1
	Figure 44.1

1.The 10 screws on each set of scissors will already be loose when shipped. Figure 44.1.

2.Expand scissors to desired height. Tighten screws to hold in place using Phillips Head screwdriver. See

Figure 44.2.

3.Measure front and side trims to required height to cover scissors and mark pieces for cutting. Cut excess mate- rial from top of trim’s edge, not bottom. This edge will be sharp; wear gloves to prevent injury to your hands.

Figure 44.2.

4.Using sheet metal shears, cut trim along the marked edge. The cut edge fits under lip of top trim, so it allows for some variance in your straight edge.

5.The double-sided tape that holds front and side trims to scissors has a particularly powerful bonding adhe- sive. Adjustments are extremely difficult once trim has adhered to tape. Do a dry run first without removing paper from tape.

6.Place cut edge of trim under top lip and into position on scissors. Place side pieces on first and then front piece. The front piece overlaps side pieces.

7.Once you are satisfied with the positioning, remove trim and set aside.

8.Remove the paper from double-sided tape that is to accept trim side. Align side and then press hard against tape to secure side piece. Repeat for other side. Install front trim piece last.

9.There are 3 holes in the back flange of the top to secure it to the wall if necessary. Use the appropriate fastener for the type of wall material, i.e., brick, sheet- rock, etc.

EXPAND SCISSORS TO DESIRED HEIGHT

INSTALL FRONT TRIM	CUT TOP EDGE
LAST. CORNERS	OF TRIM, NOT
OVERLAP SIDE TRIM	BOTTOM EDGE
PIECES

Figure 44.2

Figure 44.3 - Installation Complete

Page 44

7046-137C

December 15, 2009

Image 44

Quadra-Fire 7046-137C ACC Wood Insert Zero Clearance Adjustable Trim Support, Adjustable from 2 inches to 10 inches

Contents

ACC Wood Insert Hot glass will cause burns ACC Wood Insert Serial Number Table of Contents ACC Wood Insert Warranty Policy ACC Wood Insert BTU & Efficiency Specifications Glass SpecificationsListing and Code Approvals Appliance Certification Operating Instructions Your Wood Appliance ACC Wood Insert Fire Safety Combustible/Non-combustible MaterialsOverfiring Seasoned Wood ACC Wood Insert Burning Process Kindling or First StageSecond Stage Final Stage Manual Timer Over-Ride ACC Wood Insert Automatic Combustion Control ACCAir Controls Start-Up Air Control Burn Rates and Operating Efficiency Correct Baffle and Blanket Positions Incorrect Baffle and Blanket Positions ACC Wood Insert Building a Fire ACC Wood Insert Wood Fuel Do not USE Chemicals or Fluids to Start a Fire Blower Operating Instructions Opacity Smoke Frequently Asked QuestionsACC Wood Insert Clear Space Maintenance and Service Chimney and Chimney Connector Inspection/CleaningCleaning Plated Surfaces Disposal of Ashes Inspect Firebrick ACC Wood Insert Glass CleaningInspect Firebrick Cont’d Baffle & Blanket Placement Troubleshooting Guide Start Fire Problems Possible Cause Solution Service Parts Replacement Glass Replacement Snap Disc Replacement ACC Wood Insert Blower Replacement Shock Risk ACC Wood Insert Door Handle Assembly Baffle & Ceramic Blanket Removal ACC Wood Insert Tube Channel Assembly Replacement Draft Design and Installation ConsiderationsGetting Started ACC Wood Insert Negative Pressure ACC Wood Insert Locating Your Stove & Chimney Chimney Termination Requirements ACC Wood Insert Rule Flat Roof Pre-Use Check List ACC Wood Insert Tools And Supplies NeededInspect Appliance and Components Dimensions and Clearances Appliance Dimensions SideWall Build On-Site Hearth Support Accessory ACC Wood Insert Zero Clearance Floor ProtectionFull Reline Required ACC Wood Insert Calculating Alternate Floor Protection Chimney Systems Venting SystemsInspections Masonry Chimney ACC Wood Insert Masonry Chimney Cont’d 36.1 ACC Wood Insert Metal Heat Circulating MasonryPrefabricated Metal Chimney Altering the Fireplace ACC Wood Insert Prefabricated Metal Chimney Cont’dSecuring Chimney Components Chimney Height / Rise and Run ACC Wood Insert Zero-Clearance FireplaceOvalizing Round Stainless Steel Liners Outside Air Kit Installation Items Needed for Installation not suppliedOption One Installation Instructions Option Two Installation Instructions Leveling Legs Flue Adapter Slide ACC Wood Insert Surround & Trim Kit Installation Cont’d Top Installation Instructions ACC Wood Insert Blower Cord Installation on Left Side Instructions Shears, Measuring Tape, Gloves ACC Wood Insert Zero Clearance Adjustable Trim SupportAdjustable from 2 inches to 10 inches Mobile Home Installation Reference Materials Exploded Drawings Figure a ACC Wood Insert Service Parts & Accessories Important this is Dated Information HOW to Order Stocked At Depot Description Comments Part Number Fasteners StockedDescription Comments Part Number ACC Wood Insert Service And Maintenance Log Date of Service Performed By Description of Service Contact Information