167
SYSTEM Chapter 9 Parameter Guide
Chapter 9
CONTROL ASSIGN
Parameter/
Range Explanation
GK PU TYPE (GK Pickup Type)
GK-3 Specifies the GK-3.
GK-2A Specifies the GK-2A.
PIEZO Specifies a piezo pickup.
GUITAR SCALE
620–660mm,
ST (648mm),
LP (628mm)
This sets the scale length for your guitar.
GK PU PHASE (GK Pickup Phase)
This sets the phase for the divided pickup and normal pickup.
The sounds from the divided pickup and normal pickup are mixed
so as to enable the proper settings.
Set this to NORMAL, and if the low-frequency range is cut, set this
to INVERS.
NORMAL The phase is left unchanged.
INVERS The phase is inverted.
GK PU DIRECTION (GK Pickup Direction)
This sets the direction for the divided pickup’s installation.
NORMAL Positioned such that the cable exits near the
6th string.
REVRSE Positioned such that the cable exits near the
1st string.
S1, S2 POS (S1, S2 Position)
This exchanges the function for the GK-3’s or GK-2A’s DOWN/S1,
UP/S2 switches.
NORMAL The switches are left unchanged.
REVRSE The DOWN/S1 switch and UP/S2 switch
are exchanged.
PICKUP
↔
BRIDGE 1st–6th
10.0–30.0mm This sets the distance of the gap between
each Divided pickup and the bridge.
The setting is disregarded when the GK PU
TYPE is set to PIEZO.
SENS 1st–6th
0–100 This sets the input sensitivity for each string.
Parameter/
Range Explanation
Controller
You can freely assign functions to the VG-99’s and FC-300’s control-
lers.
GK VOL GK-3 GK volume knob
GK S1, S2 GK-3 DOWN/S1, UP/S2 switch
CTL1 Control button1
CTL2 Control button2
EXP PEDAL Expression pedal connected to the EXP
PEDAL jack
CTL3 Footswitch connected to the CTL3,4 jack
(jack tip)
CTL4 Footswitch connected to the CTL3,4 jack
(jack ring)
FC-300 EXP1 FC-300 expression pedal1
FC-300 EXP SW1 FC-300 expression pedal switch1
FC-300 EXP2 FC-300 expression pedal2
FC-300 EXP SW2 FC-300 expression pedal switch2
FC-300 CTL1 FC-300 control pedal1
FC-300 CTL2 FC-300 control pedal2
FC-300 E3/C3 FC-300 external expression pedal3/external
footswitch3
FC-300 CTL4 FC-300 external footswitch4
FC-300 E4/C5 FC-300 external expression pedal4/external
footswitch5
FC-300 CTL6 FC-300 external footswitch6
FC-300 E5/C7 FC-300 external expression pedal5/external
footswitch7
FC-300 CTL8 FC-300 external footswitch8
ASSIGN HOLD
This setting determines whether or not the values (positions) of the
D BEAM (H) or RIBBON CONTROLLER or the FC-300’s expression
pedals or control pedals or other controllers are to be reflected in the
sound as soon as a patch is called up.
ON When a patch is called up, the controller val-
ues (positions) are applied, producing a
sound that reflects the controller settings.
OFF When a patch is changed, the sound set in
the patch is played, regardless of the
controller values (positions).
VG-99_e.book 167 ページ ２００７年７月５日　木曜日　午前９時２２分