Slide the cabinet attaching the bracket in Step | Samsung 7100

OfficeServ 7100 Installation Manual

2)Slide the cabinet attaching the bracket in Step 1.

Figure 2.3 Rack Installation (2)

3)Align the two holes of the cabinet bracket and the holes of the rack brackets, and fasten the cabinet to the rack with the two screws.

Figure 2.4 Rack Installation (3)

© SAMSUNG Electronics Co., Ltd.

2-3

Image 27

Samsung 7100 installation manual Slide the cabinet attaching the bracket in Step

Contents

Installation Manual Copyright Trademarks Page Page Purpose Document Content and Organization Connecting Stations and Additional Equipment ConventionsStarting the System OfficeServ 7100 Programming Manual ReferenceRevision History OfficeServ 7100 System Manual This page is intentionally left blank Symbols RestrictionInstruction Use of Double-pole/neutral fusing Location Telephone line cord Safety Instructions for Rack MountProhibition of Metal Accessories Separation of TNV and Selv Pluggable a Board Reset Un-allowed Use of Selector SwitchAC Power Connection Inhibited Check of Power-off This page is intentionally left blank Table of Contents Connecting Stations Connecting the Grounding WireConnecting External Batteries Connecting the Power Abbreviation List of Figures List of Tables XVI Site Information Before InstallingSafety Conditions Temperature and Humidity Power Conditions Power Standards Power SupplyGrounding Conditions Checking the Package Package Items Category Name Quantity RemarkUTP Cable Types This page is intentionally left blank Installing Cabinets Procedure for the System InstallationSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a Wall With a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall External Grounding Connecting the Grounding Wire Mounting and Replacing Boards Cabinet Configuration Mountable Boards on Slots Cabinet Parts on the Rear Panel of the CabinetPart Function Mounting Control Boards Setting Switches and Mounting Option BoardsSwitches of MP10/11 Board Description Not-used Always default 3 digits Mounting a Modem Board on the MP10/11 Board Mounting Control Boards Control Board TypesControl Board Mountable Slot Mounting Interface Boards Setting Switches and Mounting Optional Boards Mounting UNI Board Tepri Boards Setting Jumpers Setting Switches Plim Board References Mounting Interface Boards to SlotsInterface Board Types and Available Slots Category Interface Board Slots Available Ошибка! Стиль не определен 13 Connecting Power Fail Transfer to a 16SLI2/8SLI Board Connecting Power Fail Transfer Removing Cables Replacing Boards 16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting an External Battery Connecting External Batteries Connecting the Power Single cabinet configuration Connecting the Power Connecting C.O. Line Line ConditionsLine condition of OfficeServ Line Condition Leak Resistance TX + RX + Connecting the C.O. LineConnecting Common C.O. Line Pin No Pin No E1 Mode Tx+ Rx+ Connecting T1/E1/PRIPage Connecting Stations Connecting Stations Additional Equipment P1 Port Pin No Connecting Analog PhonesConnecting to the 4SLM of a UNI Board Connecting to a 8SLI/16SLI2 Board RJ-45 Port of 8COMBO Board for Analog Phone Connection Connecting to a 8COMBO Board P1-P4 Ports Pin No Connecting Digital PhonesConnecting to the 4DLM of a UNI Board Connecting to a 8DLI/16DLI2 Board DLI TIP IP Phone Layout Connecting IP Phones MMC Related Connecting to a Door Phone and a Door LockConnecting to 8DLI/16DLI2/4DLM Boards Tx+ Rx+ Connecting MOH/BGM Equipment Connecting Additional Equipment Connecting Common Bell Connecting External/Additional Page Equipment About the board reset Changing System Setting Connecting Smdr Getting access to WebMMC from a client PCSpecification of the Smdr System Category 14 Connecting Smdr Connecting Printers Starting the System Pre-CheckEnvironment Safety Conditions Starting the System If the Multi MediaMMC Card is not detectedBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Checking System Operation Station Call FunctionStation Camp-On Function 4 C.O. Line Camp-On Function 3 C.O. Line Call Function Abbreviation KDB Installation Manual