Installation on a Wall | Samsung 7100 instruction

OfficeServ 7100 Installation Manual

7)Align the screws on the bottom of the OfficeServ 7100 cabinet to the bracket holes, then pull down the cabinet to fix the cabinet completely.

2 mm

Figure 2.12 Installation on a Wall (7)

© SAMSUNG Electronics Co., Ltd.

2-7

Image 31

Samsung 7100 installation manual Installation on a Wall

Contents

Installation Manual Copyright Trademarks Page Page Purpose Document Content and Organization Conventions Connecting Stations and Additional EquipmentStarting the System OfficeServ 7100 Programming Manual ReferenceRevision History OfficeServ 7100 System Manual This page is intentionally left blank Restriction SymbolsInstruction Use of Double-pole/neutral fusing Location Telephone line cord Safety Instructions for Rack MountProhibition of Metal Accessories Separation of TNV and Selv Pluggable a Board Reset Un-allowed Use of Selector SwitchAC Power Connection Inhibited Check of Power-off This page is intentionally left blank Table of Contents Connecting Stations Connecting the Grounding WireConnecting External Batteries Connecting the Power Abbreviation List of Figures List of Tables XVI Site Information Before InstallingSafety Conditions Temperature and Humidity Power Standards Power Supply Power ConditionsGrounding Conditions Package Items Category Name Quantity Remark Checking the PackageUTP Cable Types This page is intentionally left blank Procedure for the System Installation Installing CabinetsSelecting Installation Method Installing in a Rack Installing in a RackTools Required Slide the cabinet attaching the bracket in Step Installing on a Wall Installing on a Wall With a hammer, drive plastic anchors into the drilled holes 10 Installation on a Wall 12 Installation on a Wall External Grounding Connecting the Grounding Wire Mounting and Replacing Boards Cabinet Configuration Parts on the Rear Panel of the Cabinet Mountable Boards on Slots CabinetPart Function Mounting Control Boards Setting Switches and Mounting Option BoardsSwitches of MP10/11 Board Description Not-used Always default 3 digits Mounting a Modem Board on the MP10/11 Board Control Board Types Mounting Control BoardsControl Board Mountable Slot Mounting Interface Boards Setting Switches and Mounting Optional Boards Mounting UNI Board Tepri Boards Setting Jumpers Setting Switches Plim Board References Mounting Interface Boards to SlotsInterface Board Types and Available Slots Category Interface Board Slots Available Ошибка! Стиль не определен 13 Connecting Power Fail Transfer to a 16SLI2/8SLI Board Connecting Power Fail Transfer Removing Cables Replacing Boards 16 Replacing a New Board This page is intentionally left blank Connecting External Batteries Connecting an External Battery Connecting External Batteries Connecting the Power Single cabinet configuration Connecting the Power Line Conditions Connecting C.O. LineLine condition of OfficeServ Line Condition Leak Resistance TX + RX + Connecting the C.O. LineConnecting Common C.O. Line Pin No Pin No E1 Mode Tx+ Rx+ Connecting T1/E1/PRIPage Connecting Stations Connecting Stations Additional Equipment P1 Port Pin No Connecting Analog PhonesConnecting to the 4SLM of a UNI Board Connecting to a 8SLI/16SLI2 Board RJ-45 Port of 8COMBO Board for Analog Phone Connection Connecting to a 8COMBO Board P1-P4 Ports Pin No Connecting Digital PhonesConnecting to the 4DLM of a UNI Board Connecting to a 8DLI/16DLI2 Board DLI TIP IP Phone Layout Connecting IP Phones MMC Related Connecting to a Door Phone and a Door LockConnecting to 8DLI/16DLI2/4DLM Boards Tx+ Rx+ Connecting MOH/BGM Equipment Connecting Additional Equipment Connecting Common Bell Connecting External/Additional Page Equipment About the board reset Changing System Setting Getting access to WebMMC from a client PC Connecting SmdrSpecification of the Smdr System Category 14 Connecting Smdr Connecting Printers Pre-Check Starting the SystemEnvironment Safety Conditions If the Multi MediaMMC Card is not detected Starting the SystemBoard LED Status & Shut-down Numbering Extensions and C.O. Lines Station Call Function Checking System OperationStation Camp-On Function 4 C.O. Line Camp-On Function 3 C.O. Line Call Function Abbreviation KDB Installation Manual