Samsung SCX-5835NX Sending a fax manually, Resending Automatically, Redialing the last number

Sending a fax

1.Press Fax from the main screen.

2.Place the originals face up in the document feeder.

3.Adjust the document settings in the Image tab.

4.Select Duplex and Resolution options in the Basic tab.

If the originals are printed on both sides of the paper, select 2 Sided with left/right arrows in the Duplex feature.

5.When the cursor is blinking in the input line, enter the fax number using the number keypad on the control panel. Or use Address on the right side of the screen, if you have stored frequently used fax numbers.

To add a number, press Add No.

6.Press Start on the control panel. The machine starts to scan and send a fax to destinations.

•If you want to send fax directly from your computer, use SmarThru Office. (See "Using SmarThru Office" on page 94.)

•When you want to cancel a fax job, press Stop before the machine start transmission. Or press the Job Status button, and select the job you want to delete, press Delete.

•If you used the scanner glass, the machine shows the message asking to place another page.

•While the machine is sending a fax, you can not send an email at the same time. (See "Scanning originals and sending through email (Scan to Email)" on page 72.)

Sending a fax manually

This method is sending a fax using On Hook Dial on the control panel.

1.Press Fax from the main screen.

2.Place the originals face up into the document feeder.

3.Adjust the document settings in the Image tab.

4.Select Duplex and Resolution options in the Basic tab.

If the originals are printed on both sides of the paper, select 2 Sided with left/right arrows in the Duplex feature.

5.Press On Hook Dial on the control panel.

6.Enter a fax number using the number keypad on the control panel.

If the number is which you have dialed recently, press the Redial/Pause button on the control panel to show ten recent fax numbers and select a fax number.

7.Press Start when you hear a high-pitched fax signal from the remote fax machine.

Color faxes are only supported when faxes are sent manually. (See "Color Mode" on page 66.)

Resending Automatically

When the number you have dialed is busy or there is no answer, the machine automatically redials the number.

To change the time interval between redials and/or the number of redial attempts, follow the steps below:

1.Press Machine Setup on the control panel.

2.Select Admin Setting. When the login message pops up, then enter password and press OK. (See "Setting the authentication password" on page 33.)

3.Press the Setup tab > Fax Setup.

4.Press Redial.

Select Redaial Term and Redial Times.

5.Press OK.

Redialing the last number

1.Press Fax from the main screen.

2.Adjust the document settings in the Image tab.

3.Place the originals face up into the document feeder.

4.Press the Redial/Pause button on the control panel to show ten recent fax numbers.

5.Select a fax number in the list and press OK. The machine automatically begins to send.

Delaying a fax transmission

You can set your machine to send a fax at a later time when you will not be present.

1.Press Fax from the main screen.

2.Place the originals face up in the document feeder.

3.Adjust the document settings in the Image tab and the Basic tab.

4.Press the Advanced tab > Delay Send. Press On.

5.Enter Job Name using the keyboard on the display, select Start Time with left/right arrows.

If you do not enter Job Name, the machine assigns the job name as 'Fax Send Job xxx'. 'xxx' number are set in order.

Start Time is the specific time you want the fax to be sent. You can set Start Time on a 24 hour basis and 15 minutes later than the current time. For example, if it is 1:00, then you can set the time starting from 1:15. If the set time is incorrect, the warning message will appear machine resets it to the current time.

6.Press OK to start storing the scanned original data into memory.

To cancel delaying a fax, press Off before sending is activated.

Adding documents to a reserved delay fax job

You can add additional documents to the delayed fax job which is saved in memory.

Faxing_ 64