|
|
|
|
|
|
|
|
|
|
| RETURN | |
| CONTROL CONTENTS |
| COMMAND |
|
| PARAMETER |
| Power ON |
| Standby mode | ||
|
|
|
|
|
|
|
|
|
|
| (or | |
RS232C Port | Off | L | N | R | S | _ | _ | _ | 0 | OK or ERR |
| ERR |
| On | L | N | R | S | _ | _ | _ | 1 | OK or ERR |
| ERR |
Auto Power Off | Off | A | P | O | W | _ | _ | _ | 0 | OK or ERR |
| ERR |
| On | A | P | O | W | _ | _ | _ | 1 | OK or ERR |
| ERR |
Fan Mode | Normal | H | L | M | D | _ | _ | _ | 0 | OK or ERR |
| ERR |
| High | H | L | M | D | _ | _ | _ | 1 | OK or ERR |
| ERR |
PRJ Mode | Front | I | M | R | E | _ | _ | _ | 0 | OK or ERR |
| ERR |
| Ceiling + Front | I | M | R | E | _ | _ | _ | 1 | OK or ERR |
| ERR |
| Rear | I | M | I | N | _ | _ | _ | 0 | OK or ERR |
| ERR |
| Rear + Front | I | M | I | N | _ | _ | _ | 1 | OK or ERR |
| ERR |
All reset |
| A | L | R | E | _ | _ | _ | 1 | OK or ERR |
| ERR |
Language | English | M | E | L | A | _ | _ | _ | 1 | OK or ERR |
| ERR |
| Deutsch | M | E | L | A | _ | _ | _ | 2 | OK or ERR |
| ERR |
| Español | M | E | L | A | _ | _ | _ | 3 | OK or ERR |
| ERR |
| Nederlands | M | E | L | A | _ | _ | _ | 4 | OK or ERR |
| ERR |
| Français | M | E | L | A | _ | _ | _ | 5 | OK or ERR |
| ERR |
| Italiano | M | E | L | A | _ | _ | _ | 6 | OK or ERR |
| ERR |
| Svenska | M | E | L | A | _ | _ | _ | 7 | OK or ERR |
| ERR |
|
| M | E | L | A | _ | _ | _ | 8 | OK or ERR |
| ERR |
| Português | M | E | L | A | _ | _ | _ | 9 | OK or ERR |
| ERR |
|
| M | E | L | A | _ | _ | 1 | 0 | OK or ERR |
| ERR |
|
| M | E | L | A | _ | _ | 1 | 1 | OK or ERR |
| ERR |
Lamp Quantity |
| T | L | P | N | _ | _ | _ | 1 | “1” |
|
|
Model Name Check |
| T | N | A | M | _ | _ | _ | 1 |
|
| |
Projector Name Setting |
| P | J | N | 0 | _ | _ | _ | 1 |
|
|
|
Projector Name Setting 1 (First four characters) *3 | P | J | N | 1 | * | * | * | * | OK or ERR |
| ERR | |
Projector Name Setting 2 (Middle four characters) *3 | P | J | N | 2 | * | * | * | * | OK or ERR |
| ERR | |
Projector Name Setting 3 (Last four characters) *3 | P | J | N | 3 | * | * | * | * | OK or ERR |
| ERR | |
Lamp Timer Reset *4 |
| L | P | R | E | _ | _ | _ | 1 | ERR |
| OK or ERR |
Note
•If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
•Fine Sync can only be set in the displayed RGB mode.
•The return value of “TLTT_ _ _1” becomes “0” when the projector is in the standby mode.
*1 The command parameters for the CLR temperature setting are as follows.
| Parameter |
|
|
5500 | _055 |
6500 | _065 |
7500 | _075 |
8500 | _085 |
9500 | _095 |
10500 | _105 |
*2 The command parameters for the Overscan setting are as follows.
| Parameter |
|
|
10% | __10 |
9% | ___9 |
8% | ___8 |
7% | ___7 |
6% | ___6 |
5% | ___5 |
4% | ___4 |
3% | ___3 |
2% | ___2 |
1% | ___1 |
0% | ___0 |
*3 For setting the projector name, send the commands in order of PJN1, PJN2 and PJN3. *4 The Lamp Timer Reset command can only be sent in standby mode.
-58