
Troubleshooting
| Problem | Check | Page | ||
|
|
| • Projector power cord is not plugged into the wall outlet. | 25 | |
|
|
| • Power to the external connected devices is off. | – | |
|
|
| • The selected input mode is wrong. | 27 | |
|
|
| • Cables incorrectly connected to rear panel of the projector. | ||
|
|
| • Remote control batteries have run out. | 11 | |
|
|
| • External output has not been set when connecting notebook | – | |
|
|
| computer. |
| |
No picture and no sound | • The cover of the lamp unit is not installed correctly. | 49,50 | |||
or projector does not start |
|
| |||
• The selected “Signal Type” is wrong. | 44 | ||||
|
|
| |||
|
|
| • The video signal format of the video equipment is not set | 43 | |
|
|
| correctly. |
| |
|
|
| • “Bright” is set to minimum position. | 29,36 | |
|
|
| • Picture adjustments are incorrectly set. | 36 | |
|
|
|
| ||
|
|
| • Video input system is incorrectly set. | 43 | |
|
|
| (COMPONENT, DVI or HDMI input) |
| |
|
|
| • Input signal type is incorrectly set. | 44 | |
|
|
|
|
| |
Color is faded or poor. |
|
| |||
|
|
|
|
| |
|
|
| • Adjust the focus. | 27 | |
|
|
| • The projection distance exceeds the focus range. | 16 | |
|
|
| (Computer input) |
| |
|
|
| • Perform “Fine Sync” Adjustments (“Clock” Adjustment) | 41 | |
|
|
| • Perform “Fine Sync” Adjustments (“Phase” Adjustment) | 41 | |
|
|
| • Noise will appear depending on the computer. | – | |
|
|
| • The “DNR” (Digital Noise Reduction) setting is not correct. | 38 | |
|
|
| • There is fog on the lens. If the projector is carried from a cold | – | |
|
|
| room into a warm room, or if it is suddenly heated, condensation |
| |
Picture is blurred; |
| ||||
may form on the surface of the lens and the image will become |
| ||||
noise appears. | blurred. Please set up the projector at least one hour before it is |
| |||
|
|
| to be used. If condensation should form, remove the power cord |
| |
|
|
| from the wall outlet and wait for it to clear. |
| |
An unusual sound is | • If the picture is normal, the sound is due to cabinet shrinkage | – | |||
occasionally heard | caused by a room temperature changes. This will not affect |
| |||
from the cabinet. | operation or performance. |
| |||
| Maintenance | • See “Maintenance Indicators/Maintenance”. | 46 | ||
indicator on the |
|
| |||
projector illuminates. |
|
| |||
Power indicator and | • “LED” is set to “Off”. | 43 | |||
lamp indicator do not come |
|
| |||
on while projecting. |
|
| |||
Picture is green when re- | • Change the input signal type setting. | 44 | |||
ceiving component signals |
|
| |||
and the signal type setting |
|
| |||
is set to COMPONENT/ |
|
| |||
| RGB 1 or 2. |
|
| ||
Picture is pink when re- |
|
| |||
ceiving RGB signals and |
|
| |||
the signal type setting is |
|
| |||
set to COMPONENT/RGB |
|
| |||
| 1 or 2. |
|
|
Appendix
-61