Siemens SAMMS-MV - page 31

29

3 Operating the SAMMS-MV Device

Function

Number

Function Description Range Step Size Default Value

F0 Select ambient temperature. 0 - 70º C 5º C 40º C

F1 Display (or change for SAMMS-MVE)

the control circuit number,

Enable/disable incomplete sequence

status.

0 - 9999 1 N/A

F2 Display the size for single-speed

controller, or the high-speed size for

two-speed motor controllers.

H3A, H3B, H3C, H6 As shown N/A

F3 Display the low-speed size for

two-speed controller. F3 is OFF for

single-speed motor controllers.

H3A, H3B, H3C, H6 As shown N/A

F4 Select the full-load current setting (I )

for the size for single-speed motor

controller or the high-speed size for

two-speed motor controllers.

H3A: 18 - 72A

H3B: 60 - 240A

H3C: 192 - 400A

H6: 320 - 720A

1A

1A

1A

2A

18

60

192

320

F4A Display the primary current if 5A

secondary CT's are used.

Function of size in F2 Function of size in F2 OFF (denotes

SAMMS sensors

in use)

F5 Select the full-load current setting (I )

for the low-speed size for two-speed

motor controllers. F5 is OFF for single

speed motor controllers.

H3A: 18 - 72A

H3B: 60 - 240A

H3C: 192 - 400A

H6: 320 - 720A

1A

1A

1A

1A

18

60

192

320

F5A Display the primary current if 5A

secondary CT's are used.

Function of size in F3 Function of size in F3 OFF (denotes

SAMMS sensors

in use)

F6 Select the service factor. 1 or 1.15 N/A 1.15

F6A Select type of motor. ODP or EFC N/A ODP

F7 Select the overload trip class. 2-23 1 10

F7A Select cold stall time. 5-100 1 10 (ODP) /

20 (EFC)

F8 Enable/disable autoreset of overload

and external trips.

ON/OFF N/A OFF

F9 Enable/disable phase unbalance

protection.

ON/OFF N/A ON

F10 Display the time to wait until the motor

can be restarted. Applies after an

overload trip with the winding, housing,

or rotor temperature above the

maximum allowed for restarting.

Real Time Value 1s N/A

F11 Enable/disable the emergency restart

capability.

ON/OFF N/A OFF

Table 3.8 Motor control and protection functions (page 1 of 2)

FLC

FLC

Contents

Main Page 1 Introduction .............................................2 2 Installing the SAMMS-MV Device.......... 7 3 Operating the SAMMS-MV Device ......11 Contents 1 Introduction Signal Words Dangerous Procedures Field Service Operation Qualified Person 1.1 About this Manual 1.2 About the SAMMS-MV Device 12345678910 11 12 13 1415 16 1.2.1 The SAMMS-MV Device Models 1.2.2 Advanced Protection for Medium-Voltage Motors 1.2.3 Overload Protection 1.2.4 Programming Control Circuits 1.2.5 Using the Standardized Control Panel Diagnostics Statistical Data about the Motor Page 2 Installing the SAMMS-MV Device 2.1 Receiving and Storing the SAMMS-MV Device 2.2 Where to Locate the Device 2.3 Mounting the Device 2.4 Connecting the Device Page 2.4.2 Grounding the Device 2.4.3 Connecting the Device to a Control Power Source 2.4.4 Connecting Input and Output Devices to the SAMMS-MV Device 2.4.5 Communications Connection Page 3 Operating the SAMMS-MV Device 3.1 Password Protection 3.2 Using the Reset/Test Push Button 3.2.1 Performing a Lamp Test 3.2.2 Performing an Overload Relay Test 3.4 Output Devices AC Outputs Control Relays Timing Relays Pilot LEDs 3.6 Ladder Diagrams 3.6.1 Library of Standard Ladder Diagrams 3.6.2 Custom Ladder Diagrams 14 12345 Figure 3.4 Assignment of pushbuttons and light bars L1 L2 L3 STOP or OFF AUTO or OFF or HAND or 15 Table 3.3 Standard control circuits 16 Table 3.3 Standard control circuits (continued) 3.7 Incomplete Sequence 3.8 Intelligent Reduced-Voltage Starting 3.9 Ridethrough Upon Loss of Power 3.10 Overload Protection Page 3.12 Protection Curves and Overload Classes 20 Iratio I Iratio I 21 Iratio I Iratio I Seconds 3.13 Ultimate Trip Level and Service Factor 3.14 Phase Unbalance 3.15 Dual Overload Protection 3.16 Jam Protection (SAMMS-MVX Only) 3.21 Repetitive Starts 3.22 Start Inhibit 3.23 Cooling Time Constants Page Size Pickup Current Range Default Pickup Current H3A 7A to I 10A H3B 7A to I 10A H3C 7A to I 10A H6 7A to I 20A 3.26 Autoreset After a Trip (SAMMS-MVX Only) 3.27 Emergency Restarting 3.28 Using the Hand Held Communicator (HHC) Page 3.28.3 UP and DOWN Keys 3.28.4 Using the ENTER Key 3.29 Using the SAMMS-MV Device Func- tions Page Page 31 F No Yes Figure 3.13 Entering and changing passwords 3.29.1 Program Mode/Passwords 3.29.2 SAMMS-MV Functions F0 - Ambient Temperature F1 - Control Circuit Number and Incomplete Se- quence Status F2 - Size for Overload Relay #1 F3 - Size for Overload Relay #2 (SAMMS-MVX Only) F4 - Full-Load Current for Overload Relay #1 Overload Relay Size Setting Range Step Default H3A 18 to 72A 1A 18 H3B 60 to 240A 1A 60 H3C 192 to 400A 1A 192 H6 320 to 720A 2A 320 F6 - Service Factor F6A - Motor Type F7 - Overload Trip Class F7A - Cold Stall Time F8 - Autoreset (SAMMS-MVX Only) F9 - Phase Unbalance Protection F10 - Display Time to Restart F11 - Emergency Restarting F12 - Ground Fault Protection or Warning F12A - Ground Fault Pickup Current Size Pickup Current Default H3A-H3C 7A-I 10A H6 7A-I 20A F13 - Set Programmable Timer #1 F14 - Set Programmable Timer #2 F16 - Trip Current F17 - Current Unbalance F18 - Display Total Elapsed Run Time of the Motor Actual Number of Hours Displayed Time 00.0 9999 999.9 10000 1000 65535 6553 65536 0.0 (roll over) F19 - Number of Motor Starts F22 - Process Current Warning Level (SAMMS-MVX Only) F23 Jam Protection (SAMMS-MVX Only) F23A Jam Pickup Current (SAMMS-MVX Only) F24 - Loss of Load Protection or Warning (SAMMS-MVX Only) F24A - Loss of Load Pickup Current (SAMMS-MVX Only) F26 - Baud Rate F27 - Address 4 Troubleshooting the SAMMS-MV Device Page Page Appendix A - Technical Specifications of the SAMMS-MV Device Page Page Page L1ALG0000 SAM6 Configuration 47 Figure A-1Figure A-1 S1 - 1 S1 - 2 S2 - 1 S2 - 2 S2 - 3 S2 - 4 S2 - 5 SWITCH # FUNCTION POSITION Figure A-2Figure A-2 Figure A-2 Overall Dimensions and Mounting Diagram Figure A-3 Figure A-3 Figure A-3 Alarm Contact Configuration Switches (SAMMS-MVX Only)