Stat ist ica l Data | Siemens SAMMS-MV specification

Appendix A Technical Specifications

Statistical Data

Elapsed motor running time	- x10
	- Range: 0.0 to 6553 (65,536 hours)
	- Unit increments: 10 hours
Number of motor starts	- x10
	- Range:0.0 to 6553 (65,536 hours)
	- Unit increments: 10 operations
Number of overload trips	- Range: 0 to 9999
	- Increments: 1 trip
Current display	Overload Relay Size	Current Increments
	H3A	1A
	H3B	1A
	H3C	1A
	H6	2A

Alarm Contacts (SAMMS-MVX Only)

Configuration	- N.C.
	- N.O.
Functions	- Impending Trip
	- Overload Trip
	- External Trip
	- Ground Fault
	- All of the above

Software Configured Control Devices

Timers	4
Timing range	Timers 1 and 2: 0 - 200 seconds selectable
	Timer 3: 1 second fixed value
	Timer 4: 30 seconds fixed value
Timer auxiliary contacts	Software instantaneous and timed contacts
Control relays	8
Auxiliary contacts	Software instantaneous contacts

45

Image 47

Siemens SAMMS-MV user manual Stat ist ica l Data

Contents

SAMMS-MV Qualified Person Contents Qualified Person Signal WordsField Service Operation About this Manual Advanced Protection for Medium-Voltage Motors SAMMS-MV Device Models Programming Control Circuits Using the Standardized Control PanelOverload Protection Light bars Change settings requires password Yes Remote inputs OneSAMMS-MV Model Outputs One Installing the SAMMS-MV Device Full voltage non-reversing connection diagram Grounding the Device SAMMS-MV device communications connections Performing an Overload Relay Test Password ProtectionUsing the Reset/Test Push Button Performing a Lamp Test Input Devices Output Devices Custom Ladder Diagrams Ladder Diagrams Library of Standard Ladder Diagrams SAMMS-MVX Standard control circuits PB1 PB2 PB3 PB4 PB5 PB6 Intelligent Reduced-Voltage Starting SAMMS-MVX Only Ridethrough Upon Loss of Power SAMMS-MVX OnlyMotor Ambient Temperature Incomplete Sequence ODP motor thermal signature Protection Curves and Overload Classes Seconds Operating the SAMMS-MV 11 Motor protection graph Jam Protection SAMMS-MVX Only Ultimate Trip Level and Service FactorPhase Unbalance Dual Overload Protection SAMMS-MVX Only Cooling Time Constants Ground Fault DetectionRepetitive Starts Start Inhibit 12 Multi-start scenario for an ODP motor Function Key Autoreset After a Trip SAMMS-MVX OnlyUsing the Hand Held Communicator HHC Emergency Restarting Motor type Overload trip class class 2 through 5A CT primary current low speed if used Service factorFunction Number 5A CT primary current if used Full load current for OLR No UP and Down Keys Using the Enter KeyUsing the SAMMS-MV Device Func- tions ON/OFF Select jam pickup current 120-400% Iflc F24 Loss of Load Select ground fault pick-up currentDefault Value Means warning 13 Entering and changing passwords F1 Control Circuit Number and Incomplete Se- quence Status Program Mode/PasswordsF0 Ambient Temperature SAMMS-MV Functions 18 to 72A Overload Setting Step Default Relay Size RangeF3 Size for Overload Relay #2 SAMMS-MVX Only F4 Full-Load Current for Overload Relay #1 F7A Cold Stall Time F6 Service FactorF6A Motor Type F7 Overload Trip Class F11 Emergency Restarting F8 Autoreset SAMMS-MVX OnlyF9 Phase Unbalance Protection F10 Display Time to Restart F13 Set Programmable Timer #1 F12 Ground Fault Protection or WarningF12A Ground Fault Pickup Current Size Pickup Current Default H3A-H3C 7A-I FLC 10A 20A F18 Display Total Elapsed Run Time of the Motor F21 Reset Motor DataF16 Trip Current F17 Current Unbalance F23A Jam Pickup Current SAMMS-MVX Only F25 Percentage of Motor Winding TemperatureF22 Process Current Warning Level SAMMS-MVX Only F23 Jam Protection SAMMS-MVX Only F27 Address F26 Baud Rate Troubleshooting Error Condition Troubleshooting Guide Error Condition Appendix a Technical Specifications Over load Spec ificat ions Stat ist ica l Data Dimensions Catalog Number SAM6 Switch # Function Position 375 Siemens Energy Automation, Inc