Menu items in the range 800 to 899, relating to audio control (Continued)

Item number

Item name

Settings

 

 

 

 

 

 

 

 

 

 

 

806

LEVEL METER SCALE

Select the mode in which digital audio levels are displayed.

 

 

 

PEAK.0

: Displays the audio level as negative values with the maximum level set

 

 

 

to 0 dB.

 

 

 

REF.0: Displays the audio level as positive and negative values with the

 

 

 

reference level set to 0 dB.

807

AUDIO OUTPUT PHASE

Select the output timing of digital audio playback signals: (SDI and AES/EBU

 

 

 

only). The reference position corresponds to a setting of 80H; when the setting

 

 

 

is less than 80H, the output timing is advanced, and when it is higher than 80H,

 

 

 

the output timing is delayed. (at 80H, 128 samples = approx. 2.7 ms, and 1

 

 

 

sample=approx. 20 µs)

 

 

 

0 ... 80 ... FF : Setting in this range

 

 

 

 

 

 

 

 

 

 

808

INTERNAL AUDIO

Select the operation of the internal audio test signal generator.

 

SIGNAL GENERATOR

 

 

 

 

: No operation

 

OFF

 

 

 

SILNC: Silent signal

 

 

 

1KHZ: At 1 kHz, –20 dB FS sine wave is supplied to all audio input channels.

 

 

 

 

 

 

 

 

 

 

809

AUDIO LEVEL METER

Set the brightness of the audio level meters.

 

DIMMER CONTROL

0 ... 7: Set in this range. 0 is the brightest, and 7 the dimmest.

 

 

 

 

 

 

 

 

 

 

823

NAU FLG PB

Controls the non-audio flag when the playback format is Digital Betacam or

 

 

 

Betacam SX.

 

Sub-item

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

CH1/CH2

During playback (except E-E mode), sets the digital audio non-audio flag as

 

 

 

follows.

 

 

 

 

: OFF (the data is audio)

 

 

 

OFF

 

 

 

ON: ON (the data is non-audio)

 

 

 

AUTO: As follows, depending on whether tape data has been confirmed.

 

2

CH3/CH4

 

• Tape data has been read and confirmed: ON or OFF, according to the data.

 

 

 

 

 

 

• Tape data has not been confirmed: Current state is maintained.

 

 

 

 

 

 

 

 

Notes

 

 

 

 

• In the Betacam SX format, audio signals only are recorded. Therefore, the non-

 

 

 

audio flag is OFF.

 

 

 

• During playback of analog tapes, the non-audio flag is OFF regardless of the

 

 

 

setting of this item.

 

 

 

• In the MPEG IMX format, the non-audio flag follows the setting of maintenance

 

 

 

menu item M372 during recording, playback, and E-E mode.

 

 

 

For more information about the maintenance menu item M372, refer to the

 

 

 

Maintenance Manual.

824

ANALOG OUTPUT

Select the analog audio signals (tracks 1 to 8) to be assigned to audio output

 

SELECT

channels 1 to 4.

 

 

 

 

 

 

 

 

 

 

 

 

Sub-item

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

CH1/CH2

 

 

 

 

: Tracks 1 and 2 assigned to audio output channels 1 and 2

 

tr1/2

 

 

 

 

tr3/4: Tracks 3 and 4 assigned to audio output channels 1 and 2

 

 

 

tr5/6: Tracks 5 and 6 assigned to audio output channels 1 and 2

 

 

 

tr7/8: Tracks 7 and 8 assigned to audio output channels 1 and 2

 

 

 

 

 

 

 

 

 

 

2

CH3/CH4

tr1/2: Tracks 1 and 2 assigned to audio output channels 3 and 4

 

 

 

 

 

 

: Tracks 3 and 4 assigned to audio output channels 3 and 4

 

 

 

tr3/4

 

 

 

 

tr5/6: Tracks 5 and 6 assigned to audio output channels 3 and 4

 

 

 

tr7/8: Tracks 7 and 8 assigned to audio output channels 3 and 4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Continued)

Chapter8 SetupMenus

Chapter 8 Setup Menus 8-17