Sony SAL35F14G - page 56

4-17

SAL35F14G (1.4/35G) (35mm F1.4G)

2. Adjusting Method

1) Move the preset ring and fix it at the fully opened position.

Fig.4-2-10

2) Adjust by rotating the iris retainer ring so that the blades of iris are just hidden within the inner diameter of iris retainer ring.

Fig.4-2-11

3) After adjustment, apply the adhesive bond (B-10) to portions shown in Fig.4-2-9.

4) Assemble the lens in the state of near completion. Perform “4-2-1. Confirmation of iris diameter”.

Note: Repeat “4-2-2. Adjustment of iris diameter” and “4-2-1. Confirmation of iris diameter” until the iris tolerance meets the specifica-

tion.

Set the preset ring at the open aperture position.

Preset lever

Diaphragm blades are hidden into the

edge completely.

Contents

Main SERVICE MANUAL Link Ver 1.1 2007.02 SAL35F14G (1.4/35G) (35mm F1.4G) 2 SPECIFICATIONS Page 1-1 SAL35F14G (1.4/35G) (35mm F1.4G) 1. SERVICE NOTE 1-1. Chemicals 1-2. Exterior Parts 1-3. Unleaded Solder Caution: 1-4. SAFETY CHECK-OUT 1-3 1-5. TROUBLESHOOTING 1-5-1. Aperture Trouble 1-4 1-5-2. Focus Trouble 2-1 2. DISASSEMBLY NOTE FOR REPAIR UNIVERSAL WRENCH How to Use Notches Holes 2-1. DISASSEMBLY 2-1-2. LENS MOUNT RIVETING BLOCK AND LIGHT INTER CEPTION TUBE Page 2-1-4. FIXED TUBE BLOCK AND DISTANCE CONTROL TUBE 2-1-5. G ORNAMENTAL RING BLOCK AND FOCUS HOLD BUTTON BASE 2-1-6. 1 GROUP, 2 GROUP AND 3 GROUP LENS BLOCK HELP HELP01 Page HELP03 HELP04 HELP05 HELP06 HELP07 HELP08 HELP09 HELP10 HELP11 A HELP12 HELP13 Note: HELP14 G7 G8 G9 G10 HELP15 HELP16 HELP17 Note: HELP18 Note: HELP19 2. Affix the DV-FH flexible to G ornamental block shown in figure. HELP20 HELP21 HELP22 HELP23 G4 G5 G6 G7 G8 G9 G10 3. REPAIR PARTS LIST 3-1. EXPLODED VIEWS 3-1-1. ORNAMENTAL RING LABEL AND MIRROR BARREL TUBE BLOCK 3-1-2. LENS MOUNT RIVETING BLOCK AND LIGHT INTER CEPTION TUBE 3-1-3. OUTER TUBE AND JOINT TUBE 3-1-4. FIXED TUBE BLOCK AND DISTANCE CONTROL TUBE 3-4 SAL35F14G (1.4/35G) (35mm F1.4G) 3-1-5. G ORNAMENTAL RING BLOCK AND FOCUS HOLD BUTTON BASE 3-5 3-1-6. 1 GROUP, 2 GROUP AND 3 GROUP LENS BLOCK 3-7 3-1-7. SELECTION PARTS Ref. No.60 Ref. No.73 Ref. No.110 D1 D2 3-2. SUPPLIED ACCESSORIES 4-1 Note: Fig.4-1-1 4-1. PREPARATIONS 4. ADJUSTMENTS Page 4-1-2. Lens Adjustment Program (ActuatorChecker) Page Page Page Page Page Page 4-1-3. Connection of Finished Inspection JIG and Lens Adjustment Program (ActuatorChecker.exe) 4-1-4. Initial Setting of ActuatorChecker 4-1-5. About Inspection Procedure of Lens Adjustment Program (ActuatorChecker) 4-13 4-2. APERTURE DIAMETER CHECK/ADJUSTMENT 4-2-1. Aperture Diameter Check 1. Preparations Fig.4-2-1 Page Page 4-2-2. Aperture Diameter Adjustment Page 4-18 4-3. PROJECTIVE RESOLVING POWER CHECK Ver 1.1 2007.02 Fig.4-3-1 Note: 1. Preparations Note: 4-19 Fig.4-3-2 Ver 1.1 2007.02 4-20 2. Checking Method Fig.4-3-3 Note: 4-4. FLANGE BACK (fF) CHECK/ADJUSTMENT 4-4-1. Flange Back (fF) Check Page 4-23 4-4-2. Over Infinity (Infinity End) Flange Back (fF) Adjustment Adjusting Method Note: Specification Table 4-4-2 4-5. FOCUS-SHIFT CHECK/ADJUSTMENT (APERTURE (AMOUNT OF SPHERICAL ABERRATION)) 4-6. LENS ROM CHECK Page 4-7. FOCUS BRUSH POSITION CHECK/ADJUSTMENT 4-7-1. Focus Brush Position Check (Search Focus Adjustment Point) Page 4-7-2. Focus Brush Position Check (Focus Adjustment Point) 4-30 3. In case of error display in the Focus Adjustment Point 4-7-3. Focus Brush Pattern Check(Focus Brush Pattern) 4-32 3. In case of error display in the Focus Pattern (near position) Page 4-8. FOCUS HOLD BUTTON CHECK (FOCUS HOLD BUTTON) Page 4-9. WRITE dSB Page Page Revision History Reverse 985210812.pdf